12.6
SUB MENU 04-04 WEEK
Allows you to enable, disable and set chrono
The week-end programming can be enabled and disabled as shown in the graphic.
NOTE: In order to avoid unwanted start
programming option at a time.
12.7
MENU 04 CHOOSE LANGUAGE
Allows you to choose the language you prefer among the available ones.
12.8
MENU 05 STAND-BY MODE
Activate the STAND-BY mode which shuts down the stove when the room temperature is above the temperature SE
of time longer than the one defined by Pr44. If the stove shuts down for this reason, you will be able to switch it on only w
following condition is fulfilled:
T set < (room T
12.9
MENU 06 BUZZER MODE
When OFF it disables the acoustic signalling.
12.10
MENU 07 INITIAL CHARGE
When the stove is switched off and cold, it allows you to pre
12.11
MENU 08 STOVE STATUS
Displays the current stove status and the status of the devices
12.12
OPERATING MODE
The standard operating mode of a controller installed on an air stove is described below. The descriptions below refer to a
controller with chrono-thermostat options.
12.13
SWITCHING THE STOVE ON
Press P4 for a couple of seconds to switch the stove on. The display signals that the stove is switched on.
12.14
START-UP STAGE
The stove start-up phases are carried out in sequence, following the set time parameters.
12.15
FAILED SWITCHING
After Pr01 time, if the fume temperature hasn't reached 50°C, the alarm goes off.
Start
Press P3 once
Press P3 once
then press P1-P2
on off Week End
then press P1
switching on time
Press P3 once
then press P1-P2
switching on time
Push P3 once, then
switching off time
Operating, installation and maintenance manual CARBONARA
04 WEEK-END PROGRAMMING
Allows you to enable, disable and set chrono-thermostat functions during the week-end (days 6 and 7, i.e. Saturday and Sunday).
end programming can be enabled and disabled as shown in the graphic.
NOTE: In order to avoid unwanted start-ups or shut-downs of the stove, enable one
programming option at a time.
MENU 04 CHOOSE LANGUAGE
Allows you to choose the language you prefer among the available ones.
BY MODE
BY mode which shuts down the stove when the room temperature is above the temperature SE
of time longer than the one defined by Pr44. If the stove shuts down for this reason, you will be able to switch it on only w
T set < (room T – Pr43)
MENU 06 BUZZER MODE
stic signalling.
MENU 07 INITIAL CHARGE
When the stove is switched off and cold, it allows you to pre-load the pellet for 90”. Start up with key P1 and stop with key P4.
MENU 08 STOVE STATUS
Displays the current stove status and the status of the devices connected to it. Scroll down to see the different pages available.
The standard operating mode of a controller installed on an air stove is described below. The descriptions below refer to a
thermostat options.
SWITCHING THE STOVE ON
Press P4 for a couple of seconds to switch the stove on. The display signals that the stove is switched on.
up phases are carried out in sequence, following the set time parameters.
ON
After Pr01 time, if the fume temperature hasn't reached 50°C, the alarm goes off.
Press P5
once
Press P3
once
Press P5
three times
Prog. Week End
Press P3 once
then press P1-P2
switching on time
Press P3 once
then press P1-P2
switching off time
Push P3 once, then
push P1-P2
switching off time
Press P4 3 times
to exit
Operating, installation and maintenance manual CARBONARA - CAR80D
19
end (days 6 and 7, i.e. Saturday and Sunday).
downs of the stove, enable one
BY mode which shuts down the stove when the room temperature is above the temperature SET for a period
of time longer than the one defined by Pr44. If the stove shuts down for this reason, you will be able to switch it on only when the
load the pellet for 90”. Start up with key P1 and stop with key P4.
connected to it. Scroll down to see the different pages available.
The standard operating mode of a controller installed on an air stove is described below. The descriptions below refer to a
Press P4 for a couple of seconds to switch the stove on. The display signals that the stove is switched on.
Press P3
once