background image

Engb

12

About trademarks and registered trademarks

!

  Pioneer is a registered trademark of PIONEER CORPORATION.

!

  SpeakON is a registered trademark of Neutrik.

The names of companies and products mentioned herein are the trademarks of their respective owners.

Specifications

Enclosure Type

Two-way passive, reflex-loaded

Frequency Response

70 Hz to 20 kHz

Sensitivity (1 W/1 m)

101 dB

Nominal Impedance

W

Power Handling

400 W RMS, 800 W Program

Maximum SPL

127 dB cont., 133 dB peak

Dispersion

90 °H × 60 °V, Rotatable

Driver Configuration

12 inch (305 mm) neodymium LF cone driver, 1.4 inch (36 mm)exit neodymium HF compression driver

Crossover

Asymmetric internal passive crossover

Connectors

2 × Neutrik SpeakON

 NL4

Dimensions (W×H×D)

380 mm × 622 mm × 360 mm (15 inch × 24.5 inch × 14.2 inch)

Weight

23 kg (50.7 lb)

Rigging and Hardware

8 × M10 threaded mounting points (4 top/4 bottom), 2 × M10 threaded mounting points on rear, 4 × M10 threaded mounting points on side (2 left/2 right),  
4 × M8 threaded points on rear (for wall mount bracket), 1 × flush handle on rear, 1 × 35 mm polemount socket

Grille

Hex punched steel

Enclosure

15 mm (0.6 inch) birch plywood

Finish

Impact-resistant, Black semi-matt textured

The specifications and design of this product are subject to change without notice.

PIONEER CORPORATION

1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan

Корпорация Пайонир

1-1, Син-Огура, Сайвай-ку, г. Кавасаки, префектура Канагава, 212-0031, Япония

Импортер: ООО "ПИОНЕР РУС"

125040, Россия, г. Москва, ул. Правды, д.26   Тел.: +7(495) 956-89-01

PIONEER EUROPE NV

Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium   TEL: 03/570.05.11

PIONEER ELECTRONICS (USA) INC.

P.O. BOX 1720, Long Beach, California 90801-1720, U.S.A.  TEL: (800) 421-1404

PIONEER ELECTRONICS ASIACENTRE PTE. LTD.

253 Alexandra Road, #04-01, Singapore 159936   TEL: 65-6472-7555

PIONEER ELECTRONICS AUSTRALIA PTY. LTD.

5 Arco Lane, Heatherton, Victoria, 3202, Australia, TEL: (03) 9586-6300

PIONEER ELECTRONICS (THAILAND) CO., LTD.

17th Fl., KPN Tower, 719 Rama 9 Road, Bangkapi, Huaykwang, Bangkok 10310  TEL: 66-2-717-0777

PIONEER TECHNOLOGY (MALAYSIA) SDN. BHD

16th Floor, Menara Uni. Asia 1008 Jalan Sultan Ismail 50250 Kuala Lumpur  TEL: 60-3-2697-2920

ӒᎣ޷ӌԥ४ϵѨ

ѯᢋѯіҀϲ෺ୣ࿆ӏ ĵıĸ ဵ Ĺ ዃ

  TEL: 886-(0)2-2657-3588

ӒᎣႬφȞॸ෬ȟԥ४ϵѨ

ॸ෬Οᓹߞؔᢋၿ ĺıĺġဵ Ķġዃ

  TEL: 852-2848-6488 

PIONEER GULF FZE

Lob 11-017, Jebel Ali Free Zone P.O. Box 61226, Jebel Ali Dubai  TEL: 971-4-8815756

PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.

Blvd.Manuel Avila Camacho 138   10 piso Col.Lomas de Chapultepec, Mexico, D.F. 11000  TEL: 55-9178-4270

PIONEER INTERNATIONAL LATIN AMERICA S.A.

Plaza Credicorp Bank, 14th Floor, Calle 50, No.120 Panama City 0816-01361 Republic of Panama  TEL: 507-300-3900

PIONEER KOREA CORPORATION (PKC)

㎶⠞⛎፲◮⿾ᩖ◮+⦦,#4540353#⇆❢㍣ᵮ⎆#ᩲ㒖ถ#ඟ᏿ᒃ#438054<#⢿㛾Ỷᗓ###

TEL: 02-777-8005

<DRB1698-B>

© 2013 PIONEER CORPORATION.

All rights reserved.

〒 212-0031 神奈川県川崎市幸区新小倉1番1号

Summary of Contents for XY-122














Reviews: