Pioneer VSX-LX504 Instruction Manual Download

Page: 57 / 203

≫

≫

≫

≫

≫

≫

5.1.2 Channel System

This is a combination of the 5.1 Channel System and front high speakers. A front high speaker is a type of height speaker.

You can select only one set of height speakers from the following three types for connection.

❏

Front High Speakers/Rear High Speakers Installation Example (

p23

)

❏

Ceiling Speakers Installation Example (

p24

)

❏

Dolby Enabled Speakers (Dolby Speakers) Installation Example (

p25

)

"Speaker Setup" settings during

Initial Setup (

p183

)

Speaker Setup

5.1.2 ch

Front High

Height 1 Speaker

Height 2 Speaker

Speaker Impedance

6 ohms or above

Zone 2 Preout

Zone 2

• Speaker Channels:

5.1.2 ch

•

Subwoofer:

Yes

•

Height 1 Speaker:

Select the

type of height speaker actually

installed.

•

Height 2 Speaker:

---

• Zone Speaker:

• Zone 2 Preout:

Set any value

(

p151

)

•

Bi-Amp:

• Speaker Impedance:

Set any

value

(

p47

)

Summary of Contents for VSX-LX504












































































































































































































Search results

Summary of Contents for VSX-LX504

Reviews:

Related manuals for VSX-LX504

Brands by name

Popular brands

Pioneer VSX-LX504, Instruction Manual

Search results

Summary of Contents for VSX-LX504

Reviews:

Related manuals for VSX-LX504

Brands by name

Popular brands