Controls and displays
04
25
En
TV
– Use to turn on/off the power of the TV.
TV VOL +/–
– Use to adjust the volume on your TV.
INPUT SELECT
– Use to select the TV input signal.
TV CH +/–
– Use to select channels.
8
Component control buttons
The main buttons (
,
, etc.) are used to control a
component after you have selected it using the input
source buttons.
The controls above these buttons can be accessed after
you have selected the corresponding input source button
(for example
DVD/LD
,
DVR/VCR
or
TV/SAT
(when
connected to a DTV)). The following controls can be
accessed when listening to the built-in tuner:
MPX
– Switches between stereo and mono reception
of FM broadcasts. If the signal is weak then switching
to mono will improve the sound quality (page 30).
DISP
– Switches between named station presets and
radio frequencies (page 31).
9
STATUS
Press to check selected receiver settings (page 66).
10
MULTIOPE
Use this button to perform multi operations (page 70).
11
SHIFT
Press to access the controls outlined in white boxes (for
example,
INPUT SELECT
), or to display the currently
selected input source in the remote control LCD.
12
SOURCE
Press to turn on/off other components connected to the
receiver (see page 68 for more on this).
13 Character display (LCD)
This display shows information when transmitting
control signals.
The following commands are shown when you’re setting
the remote to control other components (see
Controlling
the rest of your system
on page 68):
SETUP
– Indicates the setup mode, from which you
choose the options below.
PRESET
– See
Selecting preset codes directly
on
page 68.
LEARNING
–
See
Programming signals from other
remote controls
on page 68.
MULTI OP
– See
Multi Operation and System Off
on
page 70.
SYS OFF
– See
Multi Operation and System Off
on
page 70.
DIRECT F
– See
Direct function
on page 70.
RENAME
– See
Renaming input source names
on
page 70.
ERASE
– See
Erasing one of the remote control button
settings
on page 69.
RESET
– See
Resetting the remote control presets
on
page 69.
READ ID
– See
Confirming preset codes
on page 69.
14 RECEIVER
Switches the remote to control the receiver (used to
select the green commands above the number buttons
(
ANALOG ATT
, etc). Also use this button to set up
surround sound (page 7, page 32). With
SHIFT
, this
selects the multi-room control (page 55), shown in the
display as
RCV/RM2
,
RCV/RM3
.
15 VOL +/–
Use to set the listening volume.
16 MUTE
Mutes the sound or restores the sound if it has been
muted (adjusting the volume also restores the sound).
17 Receiver controls
SIGNAL SEL
– Use to select an input signal (page 28).
SBch
– Use to select the surround/virtual back
channel mode (page 29).
STEREO
– Switches between direct and stereo
playback. Direct playback bypasses the tone controls
and any other signal processing for the most
accurate reproduction of a source (page 28).
THX
– Press to select a Home THX listening mode
(page 27).
STANDARD
– Press for Standard decoding and to
switch between the various Pro Logic IIx and Neo:6
options (page 26).
ADV.SURR
– Use to switch between the various
surround modes
(page 27).
18
PHASE
– Press to switch on/off phase correction
(page 9).
MCACC
– Press to switch between MCACC presets
(page 28).
S.DIRECT
– Press to select Auto Surround (page 26)
or Stream Direct (page 28) listening.
VSX_74TXVi.book.fm 25 ページ ２００５年６月６日 月曜日 午後７時８分
