6
En
WARNING
•
Keep the battery out of the reach of children. Should the battery be swallowed, consult a doctor
immediately.
•
Do not expose the battery or remote control to excessive heat such as direct sunlight or fire.
CAUTION
•
There is a potential danger of explosion if the battery is incorrectly replaced. When replacing the
battery, replace it with the same type.
•
Do not handle or store the battery with metallic tools or objects.
•
If the battery leaks, remove the battery and wipe the remote control completely clean. Then install a
new battery.
•
When disposing of used batteries, compliance with governmental regulations or environmental
institutions’ rules that apply in your country/area must be followed that pertain to any special
handling needed for disposal.
•
“Perchlorate Material - special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate. (Applicable to California, U.S.A.)”
Important
•
Do not store the remote control in high temperatures or direct sunlight.
•
Do not let the remote control fall onto the floor, where it may become jammed under the brake or
accelerator pedal.
When you turn the ignition switch to ON after installation, [SET UP :YES] appears in the
display.
1
Press the
M.C.
dial.
The setup menu disappears after 30 seconds of no operation. If you prefer not to set
at this time, turn the
M.C.
dial to select [NO], then press to confirm.
2
Turn the
M.C.
dial to adjust the hour, then press to confirm.
The indicator moves to the minute setting automatically.
3
Turn the
M.C.
dial to adjust the minute, then press to confirm.
[QUIT] appears.
4
Turn the
M.C.
dial to select [YES], then press to confirm.
NOTES
•
You can cancel the menu setting by pressing
SRC/OFF
.
•
This setting can be made at any time. See page 14 for more details.
1
Press the
M.C.
dial to display the main menu.
2
Turn the
M.C.
dial to select [SYSTEM], then press to confirm.
3
Turn the
M.C.
dial to select [DEMO OFF], then press to confirm.
4
Turn the
M.C.
dial to select [YES], then press to confirm.
1
Press and hold
SRC
/
OFF
until the unit turns off.
2
Press the
M.C.
dial to display the main menu.
3
Turn the
M.C.
dial to select [INITIAL], then press to confirm.
4
Turn the
M.C.
dial to select an option, then press to confirm.
Setting the clock (CLOCK SET)
Canceling the demonstration display (DEMO OFF)
INITIAL settings
Menu Item
Description
SP-P/O MODE
Select when there is a full-range speaker connected to the rear
speaker output leads and there is a subwoofer connected to the
RCA output.
[REAR/SUB.W]
[SUB.W/SUB.W]
Select when there is a passive subwoofer connected directly to
the rear speaker output leads and there is a subwoofer
connected to the RCA output.
[REAR/REAR]
Select when there are full-range speakers connected to the rear
speaker output leads and RCA output. If there is a full-range
speaker connected to the rear speaker output leads, and the
RCA output is not used, you may select either [REAR/SUB.W] or
[REAR/REAR].
S/W UPDATE
Select to update the unit to the latest Bluetooth software. For
details on Bluetooth software and updating, visit our website.
SYSTEM RESET
Select [YES] to initialize the unit settings. The unit will be
restarted automatically. (Some of the settings will be retained
even after resetting the unit, such as Bluetooth pairing
information, etc.)
[YES], [CANCEL]
Summary of Contents for MVH-X370BT
Page 23: ...23 En English ...
Page 47: ...25 Fr Français ...
Page 70: ...24Es ...
Page 71: ...25 Es Español ...
