Pioneer Elite VSX-LX104 Instruction Manual Download Page 98

Page: 98 / 152

Setup

≫

≫

≫

≫

≫

≫

System Setup

Menu list

You can configure advanced settings to have a more enjoyable experience with this unit. For operation details, refer to "Menu operations" (

p100

Input/Output

Assign

TV Out / OSD

Make settings for TV output and On-Screen Displays (OSD) that appear on the TV.

p101

HDMI Input

Change input assignment between the input selectors and HDMI IN jacks.

p102

Digital Audio Input

Change input assignment between the input selectors and DIGITAL IN COAXIAL/OPTICAL jacks.

p102

Analog Audio Input

Change input assignment between the input selectors and AUDIO IN jacks.

p103

Input Skip

You can skip inputs to which nothing is connected when selecting them with the INPUT

SELECTOR dial on the main unit or with the input selectors on the remote controller.

p103

PERSONAL PRESET

Information

Confirm the registered contents of PERSONAL PRESET.

p103

Speaker

Configuration

Change the settings of connection environment of the speakers.

p104

Crossover

Change the settings of crossover frequencies.

p105

Distance

Set the distance from each speaker to the listening position.

p106

Channel Level

Adjust the volume level of each speaker.

p107

Dolby Enabled Speaker

Change the settings of Dolby Enabled Speakers.

p108

Speaker Virtualizer

The Speaker Virtualizer function can be switched between On and Off.

p108

Audio Adjust

Dual Mono/Mono

Change the settings of multiplex audio playback.

p108

Dolby

Change the setting of when Dolby signals are input.

p108

Volume

Change the Volume settings.

p109

Source

Input Volume Absorber

Adjust the volume level when there are differences in volume level among multiple devices

connected to this unit.

p109

Name Edit

Set an easy name for each input.

p110

Audio Select

Select the priority for input selection when multiple audio sources are connected to one input

selector.

p110

Summary of Contents for Elite VSX-LX104

























































































































































Search results

Summary of Contents for Elite VSX-LX104

Reviews:

Related manuals for Elite VSX-LX104

Brands by name

Popular brands

Pioneer Elite VSX-LX104, Instruction Manual

Search results

Summary of Contents for Elite VSX-LX104

Reviews:

Related manuals for Elite VSX-LX104

Brands by name

Popular brands