Pioneer Elite VSX-LX104 Instruction Manual Download Page 114

Page: 114 / 152

114

≫

≫

≫

≫

≫

≫

Setting Item

Default Value

Setting Details

Bluetooth Wakeup Off

This function wakes up the unit on standby by

connecting a BLUETOOTH-enabled device.

"On": When this function is used

"Off": When this function is not used

•

When this function is set to "On", the power

consumption in standby state increases,

however, the increase in power consumption

is minimized by automatically entering the

HYBRID STANDBY mode where only the

essential circuits operate.

•

This setting is fixed to "Off" if "Network/

Bluetooth" - "Bluetooth" - "Auto Input Change" is

set to "Off".

•

Wait for a while if "Network Standby" and "Bluetooth Wakeup" cannot be selected. It can

be selected when the network function is activated.

12V Trigger

Set when outputting the control signal (maximum 12 V/100 mA) through the 12V

TRIGGER OUT jack. Different settings can be set for each input selector. You can

enable power link operation when you connect the unit and the external devices

equipped with 12V trigger input jack.

Setting Item

Default Value

Setting Details

BD/DVD

Off

Set the 12V trigger output setting to each input.

"Off": No output

"Main": Output when "BD/DVD" is selected as input

source for the main room.

"Zone 2": Output when "BD/DVD" is selected as

input source for Zone 2.

GAME

Off

Set the 12V trigger output setting to each input.

"Off": No output

"Main": Output when "GAME" is selected as input

source for the main room.

"Zone 2": Output when "GAME" is selected as input

source for Zone 2.

CBL/SAT

Off

Set the 12V trigger output setting to each input.

"Off": No output

"Main": Output when "CBL/SAT" is selected as

input source for the main room.

"Zone 2": Output when "CBL/SAT" is selected as

input source for Zone 2.

STRM BOX

Off

Set the 12V trigger output setting to each input.

"Off": No output

"Main": Output when "STRM BOX" is selected as

input source for the main room.

"Zone 2": Output when "STRM BOX" is selected as

input source for Zone 2.

HDMI 5

Off

Set the 12V trigger output setting to each input.

"Off": No output

"Main": Output when "HDMI 5" is selected as input

source for the main room.

Summary of Contents for Elite VSX-LX104

























































































































































Search results

Summary of Contents for Elite VSX-LX104

Reviews:

Brands by name

Popular brands

Pioneer Elite VSX-LX104, Instruction Manual

Search results

Summary of Contents for Elite VSX-LX104

Reviews:

Brands by name

Popular brands