Pioneer CX-3116 Service Manual Download Page 26

Page: 26 / 63

CX-3168

a.Tray separation operation

The rotary motion of the cam gear motor is transferred to the cylindrical cams by way of its cam. The tray is

separated by rotations of the cylindrical cams. This makes a space into which the CRG is inserted when playing
the disc. The mechanism of the cylindrical cams to separate the tray is as shown below.

In addition, the appearance of trays being separated at the time of loading or playing disc #3 is shown below as

an example.

3F ELEV O.K.

(LOAD)

Stage 1F

Tray group 3F

DISC#3 LOAD

Stage 1F

Tray group 3F

3F ELEV O.K.

(PLAY)

Stage 3F

Tray group 1F

DISC#3 PLAY

Stage 3F

Tray group 1F

Cylindrical cam, green: It is

mounted on the stage. It
moves up and down in
synchronous with the stage.

Cylindrical cam, yellow: It is

mounted on the upper tray holder.
It goes up in synchronous with
the holder.

Cylindrical cam, red: It is fixed on

the chassis.

Cylindrical cam, green: Used to select a

target tray

Cylindrical cam, yellow: Used to support the

tray at the time of loading a disc

Cylindrical cam, red: Used to support the

tray at the time of playing a disc

Summary of Contents for CX-3116
































































Search results

Summary of Contents for CX-3116

Reviews:

Related manuals for CX-3116

Brands by name

Popular brands

Pioneer CX-3116, Service Manual

Search results

Summary of Contents for CX-3116

Reviews:

Related manuals for CX-3116

Brands by name

Popular brands