Pilz PSEN opII4H Series Operating Manual Download Page 37 | Manualshive

Page: 37 / 57

Pilz PSEN opII4H Series Operating Manual Download Page 37

PSEN opII4H Series

Operating Manual PSEN opII4H Series
1003501-EN-02

37

Meaning

red

red

green

green

green

Interfering light error
OSSDs have changed to the OFF
state due to incident interfering
light.

1. Install an opaque surface on

the side facing the interfering
light source

or

reverse the positions of the
safety light grid’s transmitter
and receiver.

2. Perform a safety light grid

.

red

red

green

Overtemperature; OSSD in the
OFF state

1. Ensure that the ambient tem-

perature corresponds to the in-
formation in the

.

2. Perform a safety light grid

.

red

red

green

Undervoltage; OSSD in the OFF
state

1. Ensure that the supply voltage

corresponds to the information
in the

.

2. Perform a safety light grid

.

Indicators on the transmitter

Meaning

green

red

green

green

Safety light grid is started

green

green

Safety light grid in operation

red

red

An error has occurred.

Perform a safety light grid

«
...
35
36
37
38
39
...
»

Summary of Contents for PSEN opII4H Series


























































Reviews:

No comments