manualshive.com logo in svg

Pilz PNOZ X4, Operating Manual, Page: 30 / 33

Share
Download
Pilz PNOZ X4 Operating Manual Download Page 30

PNOZ X4

Operating Manual PNOZ X4
19894-EN-07

30

Safety characteristic data

NOTICE

You must comply with the safety-related characteristic data in order to
achieve the required safety level for your plant/machine.

Operating
mode

EN ISO
13849-1:
2008

PL

EN ISO
13849-1:
2008

Category

EN 62061

SIL CL

EN 62061

PFH

D

 [1/h]

IEC 61511

SIL

IEC 61511

PFD

EN ISO
13849-1:
2008

T

M

 [year]

–

PL e

Cat. 4

SIL CL 3

2,31E-09

SIL 3

2,03E-06

20

All the units used within a safety function must be considered when calculating the safety
characteristic data.

INFORMATION

A safety function's SIL/PL values are 

not

 identical to the SIL/PL values of

the units that are used and may be different. We recommend that you use
the PAScal software tool to calculate the safety function's SIL/PL values.

Supplementary data

CAUTION!

It is essential to consider the relay's service life graphs. The relay outputs'
safety-related characteristic data is only valid if the values in the service life
graphs are met.

The PFH value depends on the switching frequency and the load on the relay output.
If the service life graphs are not accessible, the stated PFH value can be used irrespective
of the switching frequency and the load, as the PFH value already considers the relay's
B10d value as well as the failure rates of the other components.

Summary of Contents for PNOZ X4


































Reviews:

No comments