background image

⦁ 

normal maintenance items/parts including valves and piston rings

⦁ 

Warranty repairs on all 240 Volt and portable units shall be on a back to base 
basis that the Claimant is required to return the Product to the nominated 
warranty agent as advised by Pilot Air, provided that such costs are not 
significant;

⦁ 

The replacement or repair of any defective part or correction of operating faults 
under any warranty specified herein is to be made only after Pilot Air, or its 
authorised representative, have examined the unit to their satisfaction, with 
their decision being final. 

⦁ 

In the circumstances where Pilot Air accepts or it is determined by Pilot Air that 
the claimant has a valid claim under this warranty, and subject to paragraph (m) 
below, Pilot Air will bear all of the claimant's reasonable and proximate 
expenses incurred as a result of claiming under this warranty. The claimant is 
to inform Pilot Air in writing to the address identified below within 21 days from 
when the claimant first makes a claim under this warranty of all such claims 
and expenses and provide it with copies of all receipts and invoices where 
relevant before any reimbursement is made by Pilot Air to the claimant. The 
claimant is responsible for all other costs of claiming under this warranty.

⦁ 

Pilot Air will not be responsible for any courier, transport or freight related 
costs whatsoever associated with the return to it of any defective Product that 
have not first been approved by it. Pilot Air reserves the right to first inspect 
any defective Product and decide how, if at all, the defective Product is to be 
returned to it. Any unapproved courier, transport or freight related costs will be 
to the claimant’s account.

Important Note:

If you acquire goods from Pilot Air as a consumer according to the Australian 
Consumer Law, our goods come with guarantees that cannot be excluded under the 
Australian Consumer Law. You are entitled to a replacement or refund for a major 

16

Summary of Contents for TM300I


















Reviews: