background image

contacting Pilot Air using the contact details below. 

Conditions of Warranties

⦁ 

The warranties specified herein are subject to the following conditions:

⦁ 

Pilot Air will not be liable for a breach of any of its warranties unless the 
Claimant provides proof of purchase of the Product and makes a written claim 
to Pilot Air at the address set out below, either within 30 days after the defect 
would have become reasonably apparent, or if the defect was reasonably 
apparent prior to installation, then the claim must be made prior to installation;

⦁ 

The warranties are not transferable;

⦁ 

The Product must be installed, operated, maintained and serviced strictly in 
accordance with the relevant Pilot Air literature current at the time of 
installation and must be installed in conjunction with the components or 
products specified in the Pilot Air literature. To obtain copies of such literature 
go to www.pilotair.com.au or telephone Pilot Air on (02) 9648 3099;

⦁ 

If the claimant chooses to rely upon any warranty specified herein the 
claimant’s sole remedy under the warranty for breach of the warranty is (at Pilot 
Air’s option) that Pilot Air will either supply replacement Product, rectify the 
affected Product or pay for the cost of the replacement or rectification of the 
affected product;

⦁ 

In the circumstances where the guarantees under the Australian Consumer Law 
do not apply in respect to the purchase of its Products, Pilot Air will not be 
liable for any losses or damages (whether direct or indirect) including property 
damage or personal injury, consequential loss, economic loss or loss of profits, 
arising in contract or negligence or howsoever arising. Without limiting the 
foregoing, Pilot Air will not be liable for any claims, damages or defects arising 
from misuse of the Product, inadequate maintenance and storage of the 
Product, repairs rendered necessary or arising from the use of non-genuine Pilot 
Air parts in the product, normal wear and tear maintenance of the Product, 
deterioration of any part of the Product due to normal wear and tear, work 

14

Summary of Contents for TM300I


















Reviews: