PIE PIE 830PM Manual Download Page 37

Page: 37 / 44

Page 35

Practical Instrument Electronics

Tel: 585.872.9350 • Fax: 585.872.2638 • [email protected] • www.piecal.com

Specifications

DC Voltage Read

Ranges and Resolution

±99.999 mV, ±999.99mV, 0 to 10.250 V, 0.00 to 60.00 V DC

Accuracy

≤ ± (0.02 % of R 0.01% Full Scale)

Input resistance

≥ 1 MΩ

Source V dc

Ranges & Resolution

-20.000 to 99.999 mV, -500.00 to 999.99 mV, 0.000 to 10.250V

Accuracy

≤ ± (0.02 % of R 0.01% Full Scale)

Source Current

≥ 24 mA

Sink Current

> 16 mA

Output Impedance

< 1 Ohm

Short Circuit Duration

Infinite

Thermocouple Source

Accuracy

≤ ± (0.02 % of R 0.01 mV)

Cold Junction Compensation

± 0.05°C; Thermistor traceable to NIST for 11 years

Output Impedance

< 1 Ohm

Source Current

> 20 mA (drives 80 mV into 10 Ohms)

Thermocouple Read

Accuracy & Cold Junction

Compensation

Same as Thermocouple Source

Input Impedance

> 1 Megohms

Open TC Threshold; Pulse

10K Ohms; <5 µamp pulse for 300 milliseconds (nominal)

RTD, OHMS and Continuity Read

Resistance Ranges

0.00 to 401.00, 0.0 to 4010.0 Ohms

Accuracy

±(0.025% of R 0.075 Ohms)

Excitation Current

1.0 mA to 401.0 Ohms, 0.5 mA to 4010 Ohms (nominal)

Continuity

0.0 to 401.0 Ohms; Beeps from 0.0 to 100.0 Ohms

pH Source

Range and Resolution

-414.00 to +414.00 pH

Accuracy in mV

≤ ± (0.02 % of Reading in mV + 0.1 mV)

Accuracy in pH

≤ ± 0.003 pH @ 25°C

Summary of Contents for PIE 830PM













































Search results

Summary of Contents for PIE 830PM

Reviews:

Related manuals for PIE 830PM

Brands by name

Popular brands

PIE PIE 830PM, Manual

Search results

Summary of Contents for PIE 830PM

Reviews:

Related manuals for PIE 830PM

Brands by name

Popular brands