background image

32

Fault Code Chart

Error Code

Description of Error

Diagnostic Instruction & Correct Action & Repair

E00

Communications Error

Check all wiring to heater. 
Reboot ECU by removing main fuse for 5 minutes. 
Replace ECU as necessary 

E01

Failed Ignition 
(Two attempts)

Heater does not start successfully within start up period.
Refer to Combustion Issues in manual. 

E02

Flame Extinguished 
(Three successive failures)

Heater establishes a flame then detects a flame out condition.
Refer to Combustion Issues in manual.

E03

High or Low Voltage

Voltage at ECU must be less than 16.0 volts and more than 10.5 volts
Repair vehicle electrical system as required

E04

Premature Ignition

Heater detect flame prior to fuel pump operation. 
Unburnt fuel in combustion chamber during start up.
Refer to Combustion Issues in manual.

E05

Thermal Efficiency Failure

Heater detects a poor combustion
Refer to Combustion Issues in manual.

E06

Temperature Sensor Open or Short Circuit

Check sensor resistance. 
Should be approximately 1.0 kΩ at room temp. Replace as necessary

E07

Fuel Pump 
Open / Short Circuit

Check fuel pump wiring connections & resistance across fuel pump terminals 
and main harness pins 10 & 11. Should be 7.5-8.5 Ω 
Repair wiring or replace fuel pump as required 

E08

Blower Motor 
Open / Short Circuit or blockage

Check blower motor wiring & blower motor for free rotation 
Repair wiring or replace blower as required

E09

Glow Pin 
Short Circuit

Check glow pin connectors and resistance across glow pin 
Should be 0.8 Ω. Replace glow pin as required. 

E10

Over Temperature

Check fan operation & for blockage of hot air ducting air flow
 (in and out) 
Check Flame / Overheat sensor resistance. 
Should be approximately 1.0 kΩ at room temp. Replace as necessary

E11

Temperature Sensor 
Short Circuit 

Check Temperature sensor resistance. 
Should be approximately 1.0 kΩ at room temp. Replace as necessary

E12

Glow Pin 
Open Circuit

Check glow pin connectors and resistance across glow pin 
Should be 0.8 Ω. Replace glow pin as required.

E14

Temperature Sensor 
Open Circuit

Check positioning of sensor to ensure proper contact with heat exchanger
Check Temperature sensor resistance. 
Should be approximately 1.0 kΩ at room temp. Replace as necessary 

E15

Open Circuit in Operating Switch potentiometer 

Replace operating switch.

Summary of Contents for PH41A





































Reviews: