background image

 

9

OPERATION 

 

StudioMax III All Models

 

Flashing Rate: 

The unit recharges quickly, as indicated by the READY light on the control 
panel.  A quick series of flashes can be obtained within the limits of the 
recharge time.  Continuous rapid flashing, however, can overheat and 
damage the flashtube and internal parts.  The maximum recommended rate 
of flashing depends upon the power level being used and the amount of 
operation time.  Use the following chart to serve as a guide for the 
maximum rate to use in your situation. 

 

Power Level 

 

Operating Time 

 

Sec. Between 

Flashes

Number of 

Flashes

Full

 

Continuous

 

15 Continuous 

 

30 minutes 

 

10 180 

 

1 minutes 

 

4 15 

 

 

 

 

1/4

 

Continuous

 

10 Continuous 

 

30 minutes

 

6 300 

 

3 minutes

 

4 45 

 

 

 

 

1/32  

1.5 Continuous 

 

Exposure Information: 

The following charts give the BCPS output for various umbrellas and reflectors.  
Coverage angle is given in degrees.  Divide numbers in half for 160 watt-second 
units. 

Umbrella 32 

inch 45 inch 

60 inch 

Coverage  

120 degree 

120 degree 

120 degree 

Full 

Power 

1658 1683 1683 

1/2 

829 841 841 

1/4 

414 421 421 

1/8 

207 210 210 

1/16 

104 105 105 

 

Reflectors None  7 

½”  14”  16” 

20”  24” 

Coverage 

360

°

 35

°

 40

°

 60

°

 65

°

 145

°

 

Full 703 

7534 

5274 

7032 

4922 

1266 

1/2 

352  3767 

2637 3516 2461 633 

1.4 

176  1884 

1318 1758 1230 316 

1/8 88 

942 

659 

879 

615 

158 

1/16 

44  471 

330 439 308 79 

1/32 

22  235 

165 220 154 39 

GN@ 
ASA 100

 

33

 

110 92

 

105 89

 

45

 

Summary of Contents for AKC160

















Reviews: