[
1
]
For lead-acid battery, default charge current is 0.15C, which is can be configurable up to 0.5C by APP Phonocube and cannot exceed
50A. C means the battery capacity, such as the battery capacity is 100Ah, default charge current 0.15C is 0.15 * 100A = 15A.
For Li-Ion battery, discharge and charge current follows the command of BMS which doesn't exceed 50A.
[
2
]
Under off-grid mode, then battery capacity should be more than 100Ah.
[
3
]
Maximum operating dc voltage is 530V
.
[
4
]
When there is no battery connected, inverter starts feeding in only if string voltage is higher than 200V.
Zref : RA = 0,24 ; XA = j 0,15 at 50 Hz;
RN = 0,16 ; XN = j 0,10 at 50 Hz.
[
5
]
4600 for VDE4105-AR-N & VDE0126-1-1
[
6
]
21.7A for Australia and New Zealand
.
[
7
]
Can be reached only if PV and battery power is enough.
13 Maintenance
Heatsink: please use towel to clean the heatsink once a year;
Torque: please use torque wrench to tighten the AC and battery terminal wiring connection once a year;
Followed 4.2 and 4.3 torque instruction.
DC swith: check the DC switch regularly, active the DC switch 10 times in a row once a year. operating the DC switch
will clean the contacts and will extand the life of the DC switch.
Waterproof covers: check if waterproof covers of RS485 and USB port is fasten once a year.
ID 1419046190
12 Certificates
59
Note
Overvoltage category definition
Category I
:
applies to equipment connected to a circuit where measures have been taken to reduce transient overvoltage to a
low level.
Category II
:
applies to equipment not permanently connected to the installation. Examples
are appliances, portable tools and
other plug-connected equipment;
Category III
:
applies to fixed equipment downstream of and including, the main distribution board. Examples are switchgear
and other equipment in an industrial installation;
Category IV
:
applies to equipment permanently connected at the origin of an installation (upstream of the main distribution
board). Example are electricity meters, primary overcurrent protection equipment and other equipment connected
directly to outdoor open lines.
Environment category definition
Outdoor : the ambient air temperature is -20~50°C, Relative humidity range is 4 % to 100 %, applied to PD3
Indoor unconditioned: the ambient air temperature is -20~50°C, Relative humidity range is 5 % to 95%,applied to PD3
Indoor conditioned: the ambient air temperature is 0~40°C, Relative humidity range is 5 % to 85%,applied to PD2
Pollution
degree
d
efinition
Pollution degree 1
:
No pollution or only dry, non-conductive pollution occurs. The pollution has no influence.
Pollution degree 2
:
Normally only non-conductive pollution occurs. Occasionally, however, a temporary conductivity caused by
condensation must be expected.
Pollution degree 3
:
Conductive pollution occurs, or, dry, non-conductive pollution occurs which becomes conductive due to
condensation which is expected.
Pollution degree 4
:
Persistent conductive pollution occurs, for example, the pollution cause by conductive dust, rain and snow.
Moisture
parameters
Level
Temperature Range
Humidity Range
3K3
0~+40
℃
5%
~
85%
4K2
-33~+40
℃
15%
~
100%
4K4H
-20~ +55°C
4%
~
100%
Moisture
location
category
definition
G100 IEC62109-1
IEC62109-2
CEI 0-21 VDE0126-1-1
VDE-AR-N 4105
27
Model
Certifications & Standards
Topology
Safety Regulation
EMC
Grid Regulation
Protective class
Standby Self Consumption (W)
IP rating
IEC62109-1&-2, IEC62040-1
AS/NZS 4777.2:2015; G83/2; G100; CEI 0-21 VDE4105-AR-N; VDE0126-1-1; NRS 097-2-1
EN61000-6-1, EN61000-6-2, EN61000-6-3, EN61000-6-4
EN 61000-4-16, EN 61000-4-18, EN 61000-4-29
<13
I
High Frequency Isolation
IP65
28
PC5.0A1-S
PC3.6A1-S
PC3.0A1-S
Summary of Contents for PC3.0A1-S
Page 1: ...340 00xxx 00 PC...
