4
USEPHOENIX.COM
1.800.533.7533
3.2 Recommended Use
Recommended use(s) of on-board duplex GFCI are shown.
Note: Standard 115 VAC electrical outlets.
4 Operation Instructions
The Phoenix Centrifugal Air Mover Pro is intended for use
by water damage restoration, carpet cleaning, construction,
and janitorial/sanitation professionals in general ventilating
and structural surface drying applications. The Phoenix
Centrifugal Air Mover Pro as packaged is ready to be put
into service. Inspect the unit completely for any shipping
damage. Place the unit on the ground. Check the GFCI to
ensure it is not tripped. Plug the unit into a grounded outlet
and select the drying mode.
CAUTION: The Phoenix Centrifugal Air Mover Pro consumes
2.6 Amps on high speed. Do not plug devices requiring more
than 9.3 Amps of current into the duplex outlet.
5 Operator Panel Features
5.1 12 Amp Resettable Circuit Breaker
The 12 AMP thermal response resettable circuit breaker
protects the unit and devices connected to its duplex GFCI
outlet.
The circuit breaker is designed to sense the total current
draw through the circuit. The circuit breaker “trips” when
more than 12 amps of electrical current are drawn through
the device’s power cord. Should an over-current condition
occur, the Centrifugal Air Movers’ on-board circuit breaker
trips thus preventing nuisance visits to a remote power
junction box.
To reset on-board breaker, remove over drawing equipment.
Allow to cool for 10 minutes and reset breaker.
IMP0RTANT: Total amperage of the Centrifugal Air Mover
plus all devices plugged into the receptacle must not
exceed 12 amps. The circuit breaker will not allow for loads
in excess of 12 amps, although there is a time delay before
the overloaded circuit is broken.
5.2 Power Indication Lamp
The red, sealed, high intensity AC voltage power indication
lamp allows operators to visually identify the operation
status of several Phoenix Centrifugal Air Mover Pros at a
distance, with a single glance. The power indication lamp
will remain lit when the AC power cord is plugged into a
standard “powered” AC power outlet and the
3-Position drying selector switch is in either the HIGH or LOW
operation position. The power indication lamp will remain
unlit when the AC power cord is unplugged, the 3-Position
drying selector switch in the OFF position, the on-board
GFCI or 12 Amp circuit breaker is tripped, or the connected,
standard AC wall outlet power has been turned off.
5.3 3-Position Drying Selector Switch
The Phoenix Centrifugal Air Mover Pro features a three-
position switch - LOW–OFF–HIGH.
1. Inspect the machine for damage and airflow
obstructions prior to plugging it in or operating it.
2. Ensure the power switch is in the OFF (middle) position.
3. Place the machine into the desired position for
operation. Ensure that the machine rests stable and
secure and will not overturn.
4. Plug the power cord into a GFCI protected outlet. Do not
use an extension cord in conjunction with the standard
power cord.
5. Turn the unit on to the desired speed, high or low.
12 Amp
Circuit Breaker
GFCI Outlet
Stainless
Steel
Control
Panel
AC Indicator
Lamp
High Speed:
“Ultra”
Drying Power
Low Speed:
Quiet Operation
Figure 3: Centrifugal Air Mover Pro Operator
Panel
4
www.usephoenix.com • [email protected]
Toll-Free 1-800-533-7533
4 Operation Instructions
The Phoenix Centrifugal Air Mover is intended for use by
water damage restoration, carpet cleaning, construction,
and janitorial/sanitation professionals in general
ventilating and structural surface drying applications. The
Phoenix Centrifugal Air Mover as packaged is ready to
be put into service. Inspect the unit completely for any
shipping damage. Place the unit on the ground. Check
the GFCI to ensure it is not tripped. Plug the unit into a
grounded outlet and select the drying mode.
CAUTION: The Phoenix Centrifugal Air Mover consumes 2.7
Amps on high speed. Do not plug devices requiring more
than 9.3 Amps of current into the duplex outlet.
5 Operator Panel Features
5.1 12 Amp Resettable Circuit Breaker
The 2 AMP thermal response resettable circuit breaker
protects the unit and devices connected to its duplex GFCI
outlet.
The circuit breaker is designed to sense the total current
draw through the circuit. The circuit breaker “trips” when
more than 2 amps of electrical current are drawn through
the device’s power cord. Should an over-current condition
occur, the Centrifugal Air Movers’ on-board circuit breaker
trips thus preventing nuisance visits to a remote power
junction box.
To reset on board breaker, remove over drawing equipment.
Allow to cool for 0 minutes and reset breaker.
IMPORTANT: Total amperage of the Centrifugal Air Mover
plus all devices plugged into the receptacle must not
exceed 12 amps. The circuit breaker will not allow for loads
in excess of 12 amps, although there is a time delay before
the overloaded circuit is broken.
5.2 Power Indication Lamp
The red, sealed, high intensity AC voltage power indication
lamp allows operators to visually identify the operation
status of several Phoenix Centrifugal Air Movers at a
distance, with a single glance. The power indication lamp
will remain lit when the AC power cord is plugged into a
standard “powered” AC power outlet and the
3-Position drying selector switch is in either the HIGH or
LOW operation position. The power indication lamp will
remain unlit when the AC power cord is unplugged, the
3-Position drying selector switch in the OFF position, the
on-board GFCI or 2 Amp circuit breaker is tripped, or the
connected, standard AC wall outlet power has been turned
off.
5.3 3-Position Drying Selector Switch
The Phoenix Centrifugal Air Mover features a three-position
switch - LOW–OFF–HIGH.
. Inspect the machine for damage and airflow
obstructions prior to plugging it in or operating it.
2. Ensure the power switch is in the OFF (middle)
position.
3. Place the machine into the desired position for
operation. Ensure that the machine rests stable and
secure and will not overturn.
4. Plug the power cord into a GFCI protected outlet. Do
not use an extension cord in conjunction with the
standard power cord.
5. Turn the unit on to the desired speed, high or low.
3.2 Recommended Use
Recommended use(s) of on-board duplex GFCI are shown.
Note: Standard 115 VAC electrical outlets.
15 Amp
Outlet
15 Amp
Outlet
15 Amp
Outlet
Phoenix 200 MAX
Phoenix Mini-Guardian
Phoenix
CAM
Phoenix
CAM
Phoenix
CAM
Phoenix
CAM
Phoenix
CAM
Phoenix
CAM
Phoenix
CAM
Phoenix
CAM
Phoenix
CAM
Figure 2: Duplex GFCI use
2 Amp
Circuit Breaker
GFCI Outlet
Stainless
Steel
Control
Panel
AC Indicator
Lamp
High Speed:
“Ultra”
Drying Power
Low Speed:
Quiet Operation
Figure 3: Centrifugal Air Mover Operator Panel
