© 2011 Phoenix Gold • www.phoenixgold.com
Amplifier Owner’s Manual
RMS Power 14.4Vdc ≤1% THD
80 x 4 @ 4 ohms Stereo
125 x 4 @ 2 ohms Stereo
250 x 2 @ 4 ohms Bridged
plus
500 x 1 @ 4 ohms
800 x 1 @ 2 ohms
Dynamic Power 14.4Vdc >1% THD
95 x 4 @ 4 ohms Stereo
150 x 4 @ 2 ohms Stereo
300 x 2 @ 4 ohms Bridged
plus
700 x 1 @ 4 ohms
1000 x 1 @ 2 ohms
Recommended Fuse Size:
100 amp
Power/Ground Wire Size:
4 Gauge
Dimensions (Includes Mounting Feet): 14.33” L x 6.93” W x 2.0” H
364mm L x 176mm W x 51mm H
Dimensions (Includes Terminals):
14.96” L x 6.93” W x 2.0” H
380mm L x 176mm W x 51mm H
RMS Power 14.4Vdc ≤ 1% THD
900 x 1 @ 2 ohms
1300 x 1 @ 1 ohm
Dynamic Power 14.4Vdc >1% THD
1200 x 1 @ 2 ohms
1600 x 1 @ 1 ohm
Recommended Fuse Size:
120 amp
Power/Ground Wire Size:
4 Gauge
Dimensions (Includes Mounting Feet): 14.33” L x 6.93” W x 2.0” H
364mm L x 176mm W x 51mm H
Dimensions (Includes Terminals):
14.96” L x 6.93” W x 2.0” H
380mm L x 176mm W x 51mm H
INPUT
Connect preamp signal cables from the head unit to these terminals.
CROSSOVER FREQUENCY
Controls the lowpass crossover point for the speaker outputs.
BASS BOOST
Variable bass boost from 0 to +18dB @ 45Hz.
REMOTE LEVEL CONTROL
This port is for connecting the subwoofer remote level control. This allows
up to 20dB of volume adjustment. This is not a bass boost, it controls the
level of the low pass signal.
NOTE: This control is not compatible with the Phoenix Gold LPL44 level
control.
SENS
Used to reach maximum amplifier power with a wide variety of headunits.
SUBSONIC CROSSOVER FREQUENCY
Controls the highpass crossover point for the speaker outputs to eliminate
extreme low frequencies.
RMD
Optional RMD Voltage Display plugs into this port. Sold separately.
+12V
This must be connected to the fused positive terminal (+12V) of the car’s
battery. The fuse must be located within 18 inches of the battery.
REMOTE
This must be connected to sw12V, usually a trigger wire coming
from the head unit or ignition.
GROUND
This must be connected to the negative terminal of the car’s battery or
bolted to a clean, unpainted part of the chassis of the vehicle.
SPEAKER OUTPUTS
Used to connect the amplifier to speakers. SD1300.1 minimum impedance
is 1 ohm.
SD1300.1
Monoblock Power Amplifier
NOTE: Visible through the plexiglass cover, a single blue power LED is located in the lower corner of all SD amplifiers.
GROUND
REMOTE
+ 12V
GROU ND
+ 12V
R
FUSE
40A
40A
40A
POWER
SENS
MIN
MAX
BASS
0dB
18dB
X-OVER
FREQ.
30Hz
300Hz
REMOTE
PROTECT
SUBSONIC
10Hz
55Hz
L
R
INPUT
RMD
SPEAKER
PROTECT
POWER
REMOTE
SUB INPUT
R
MIN
MAX
MIN
MAX
SENS
SENS
BASS BOOST
0dB
18dB
HPF
15Hz
250Hz
HPF
15Hz
250Hz
MIN
MAX
SENS
30Hz
LPF
300Hz
GROUND
REMOTE
+ 12V
FL
SUB.
SUB.
INPUT
RR
RL
FR
FL
SUB INPUT
L
S UB
FRONT
FRONT
REAR
FR
RL
RR
GROU ND
+ 12V
R
RMD
