background image

Amplifier Owner’s Manual

© 2011 Phoenix Gold • www.phoenixgold.com  

Specifications

SD1300.5 SPECIFICATIONS

Frequency Response: 

             ± 1dB from 20Hz to 20kHz

Signal to Noise Ratio: 

             >100dB

High Pass Crossovers: 

             12dB per Octave

Low Pass Crossover: 

             18dB per Octave

High Pass Crossover Range: 

             15Hz to 250Hz

Low Pass Crossover Range: 

             30Hz to 300Hz

Bass Boost @ 45Hz:                                                         0 to +18dB

Low Level Input Range: 

             200 millivolts to 8 volts

Front and Rear Channels Lowest Load:               4 ohms Bridged or 2 ohms Stereo

Subwoofer Channel Lowest Load: 

             2 ohm

Typical Efficiency: 

             70%

Damping Factor 

             Greater than 200

Note: All SD amplifiers operate correctly up to 14.4 volts. Do not 

operate the amplifier above 14.4 volts. The amplifier will engage its 

overvoltage protection, the result is no audio output on one or 

more channels. 

 

RMS Power 14.4Vdc ≤1% THD 

80 x 4 @ 4 ohms Stereo

 

125 x 4 @ 2 ohms Stereo

 

250 x 2 @ 4 ohms Bridged

 

 

plus

 

500 x 1 @ 4 ohms

 

800 x 1 @ 2 ohms

 

Dynamic Power 14.4Vdc >1% THD 

95 x 4 @ 4 ohms Stereo

 

150 x 4 @ 2 ohms Stereo

 

300 x 2 @ 4 ohms Bridged

 

 

plus

 

700 x 1 @ 4 ohms

 

1000 x 1 @ 2 ohms

Recommended Fuse Size: 

100 amp

Power/Ground Wire Size: 

4 Gauge

Dimensions (Includes Mounting Feet):           14.33” L x 6.93” W x 2.0” H

 

        364mm L x 176mm W x 51mm H

Dimensions (Includes Terminals):  

        14.96” L x 6.93” W x 2.0” H

 

        380mm L x 176mm W x 51mm H

SD1300.1 SPECIFICATIONS

Frequency Response:  

± 1dB from 20Hz to 300Hz

Signal to Noise Ratio:  

>90dB

Low Pass Crossover:  

18dB per Octave

Subsonic Filter:  

12dB per Octave

Low Pass Crossover Range:  

30Hz to 300Hz

Subsonic Crossover Range:  

10Hz to 55Hz

Bass Boost @ 45Hz:  

0 to +18dB

Low Level Input Range:  

200 millivolts to 8 volts

Lowest Recommend Load:  

1 ohm

Typical Efficiency:  

70%

Damping Factor:  

Greater than 200

RMS Power 14.4Vdc ≤ 1% THD  

        900 x 1 @ 2 ohms 

 

        1300 x 1 @ 1 ohm

Dynamic Power 14.4Vdc >1% THD 

        1200 x 1 @ 2 ohms

 

        1600 x 1 @ 1 ohm

Recommended Fuse Size:  

        120 amp

Power/Ground Wire Size:  

        4 Gauge

Dimensions (Includes Mounting Feet):           14.33” L x 6.93” W x 2.0” H

 

        364mm L x 176mm W x 51mm H

Dimensions (Includes Terminals):  

        14.96” L x 6.93” W x 2.0” H

 

        380mm L x 176mm W x 51mm H 

 

Summary of Contents for SD1300.1













Reviews: