Phoenix Gold RSD300.1 Owner'S Manual Download

Page: 5 / 8

Phoenix Gold International, Inc. • 9300 North Decatur St. Portland, OR 97203 • 503.286.9300 • www.phoenixgold.com

RSd AMPLIFIERS

MONOBLOCK OWNER’S MANUAL

11. AMP FUSE

Protects the ampliﬁer. If a replacement is necessary, use the same size and

type indicated on the end panel. Never use a fuse with a higher amp rating.

12. PROTECT LED

Red light:

Ampliﬁer is in protection - Overheated (will resume play on its

own), Low voltage, Shorted terminal

No light:

Ampliﬁer is functional (when power is on)

Note: “Power On” is indicated when the badge/logo on top of the ampliﬁer

lights up blue

13. RMD PORT (RMD - SOLD SEPERATELY)

This connection allows for connection of our remote voltage display

(optional), so that you can monitor the applied voltage at the ampliﬁer in real
time.

14. LEFT/RIGHT SPEAKER OUTPUT TERMINAL

Used to connect the ampliﬁer to speakers. The minimum suggested speaker
wire size is 16 gauge for stereo mode and 14 gauge if the ampliﬁer is going to
be used in mono/bridged operation.

��

�

��

8. GROUND INPUT TERMINAL (B-)

To be wired to the vehicle’s chassis for ground.

9. REMOTE TURN-ON INPUT TERMINAL (R)

To be connected to the remote control wire or power antenna lead of the

source unit for remote ON/OFF.

10. POWER INPUT TERMINAL (B+)

To be connected to the positive terminal of the vehicle’s battery or other

co12 V source. Remember to fuse at 12+ source.

POWER INPUT

SPEAKER OUTPUT AND FUSING

Summary of Contents for RSD300.1









Search results

Summary of Contents for RSD300.1

Reviews:

Related manuals for RSD300.1

Brands by name

Popular brands

Phoenix Gold RSD300.1, Owner'S Manual

Search results

Summary of Contents for RSD300.1

Reviews:

Related manuals for RSD300.1

Brands by name

Popular brands