background image

3. Daily operation

The OSD menu time-out value can be adjusted in the OSD menu (

OSD menu time-out

).

The OSD lock function can be enabled or disabled in the OSD menu (

OSD lock

).

The OSD menu position can be adjusted in the OSD menu (

OSD menu position

).

To navigate through the OSD menus

Use the

or

key to scroll up or down through the different menu pages, change values or make

selections.

To go into a submenu or con

fi

rm adjustments and selections, use the

key.

To exit a menu or return to the previous menu level, scroll the top level item of the current menu, then
press the

key.

3.4

Brightness adjustment

To adjust the brightness

If the OSD is locked (default setting),

fi

rst press and hold both the

and

keys for approximately

3 seconds, until a pop up warns you that the OSD has been unlocked for about 20 sec. Afterwards,
press the brightness increase ( ) or brightness decrease ( ) keys to adjust the brightness as desired.

Or,

If the OSD is not locked, press the brightness increase ( ) or brightness decrease ( ) keys to adjust the
brightness as desired.

The OSD lock function can be enabled or disabled in the OSD menu (

OSD lock

).

To force MAX brightness ON

When brightness is at 100%, by keeping the Up / Brightness increase key ( ) pressed for at least 3
seconds, the brightness is forced to the MAX brightness mode, which adds up 20 cd/m² to the default
stabilized brightness value. Press the Menu / Enter key ( ) to exit the MAX brightness mode.

12

K5902096 (451920611523) PS24FHDCR 08/03/2018

Summary of Contents for PS24FHDCR















































Reviews: