background image

ANT. IN

AC 120V

OR

OR

To either
Antenna Hole

Round cable of

Rod Antenna

to ANT. IN

Round Cable

75

 to ANT. IN

Back of TV

Rod Antenna

(supplied)

Combination

VHF/UHF Antenna

(outdoor or indoor)

Twin-lead wire

300 to 75

 adapter

to ANT. IN

ANT. IN

AC 120V

OR

UHF

VHF

300

75

-300

 

 A

D

A

P

TE

R

H

OOKING

U

P

Y

OUR

TV (A

NTENNA

/C

ABLE

C

ONNECTIONS

)

A

combination antenna or a
rod antenna (supplied)

receives normal broadcast
channels (VHF 2-13 and UHF
14-69). Your connection is easy
since there is only one 75

(ohm) antenna jack on the
back of your TV - and that’s
where the antenna goes.  

A

NTENNA

C

OMBINATION

UHF/VHF

To set the
TV to select only
the channel num-
bers in your area,
see Auto Install on
page 5.

If you install the TV
beneath a kitchen
cabinet, you may
push a rod antenna
into the antenna
hole on the bottom
of the TV cabinet
for the best use. See
page four for details
on how to install
the TV under a
kitchen cabinet.

S

MART

H

ELP

If you install a rod

antenna (supplied), push the
base of the antenna into the
antenna hole on either the left
or the bottom of the TV.
If your antenna has a
round connector (75

),

then you're ready to connect it
to the TV. Go to step 2.
If your antenna has flat
twin-lead wire (300

), you

first need to attach the antenna
wires to the screws on a 300
to 75

adapter (not supplied).

Push the round end of

the adapter (cable or rod
antenna) onto the
ANT(enna) IN jack on the
back of the TV. 
If the round
end of the adapter or cable is
threaded, screw it down tight.

Y

ou may have two separate
antennas. One antenna is

for VHF channels (2-13) and
the other antenna is for UHF
channels (14-69).
For homes with separate
UHF/VHF antennas, you will
need an optional combiner
before you can connect the
antennas to the TV.

S

EPARATE

UHF/VHF

Back of TV

UHF/VHF Combiner

(not supplied)

75-300

Adapter

Outdoor UHF Antenna

(Twin-lead 300

)

Outdoor VHF

Antenna

(Twin-lead 300

)

Twin-lead

Wire

Push the round end of the

combiner onto the ANT(enna)
IN jack on the back of the TV. 

Attach the separate

UHF and VHF antennas to
the correct screws on the
combiner (not supplied).

Round

End

Outdoor VHF

Antenna

(Round cable 75

)

- 2 - 

If you installed a rod

antenna, extend the antenna
and adjust its length, direction,
and angle for the clearest pic-
ture.

PR0930x4  3/1/02  10:21 AM  Page 2

All manuals and user guides at all-guides.com

Summary of Contents for PR0930X









Reviews: