background image

HD6596/50/G /51/G

8-18

Manual pump adjustment

1. 

Keep the 1-cup and 2-cup button pressed while connecting the appliance to the mains.

2. 

The buttons can be released when the 1-cup and 2-cup LEDs are switched on.

You entered automatically the 1-cup pump time adjusting step.

3. 

1-cup adjustment:

a.  Press and release the 1-cup button to decrease the calibration value.

The 1-cup and 2-cup LEDs blink one time.

b.  Press and release the 2-cup button to increase the calibration value.

The 1-cup and 2-cup LEDs blink one time.

4. Store 

new 

1-cup

 pump time values:

Press and release the 1-cup and 2-cup buttons to store the calibration value.

The 1-cup and 2-cup LEDs blink rapidly 3 times.

You enter automatically the 2-cup pump time adjusting step, 1-cup and 2-cup buttons are on.

5. 

2-cup adjustment:

a.  Press and release the 1-cup button to decrease the calibration value.

The 1-cup and 2-cup LEDs blink one time.

b.  Press and release the 2-cup button to increase the calibration value.

The 1-cup and 2-cup LEDs blink one time.

6. Store 

new 

2-cup

 values:

Press and release the 1-cup and 2-cup buttons to store the calibration value.

The 1-cup and 2-cup LEDs blink rapidly 3 times.

Intensity select (scale factor calibration)

Depending if the “intensity select” feature is enabled or disabled the 1-cup or 2-cup LED is switched on.

See table below:

Intensity select disabled

(HD7892 & HD6591)

1-cup LED is on

2-cup LED is off 

Intensity select enabled

(HD6592 & HD6596)

1-cup LED is off 

2-cup LED is on

7. 

Check/press the desired button following the above table for the desired state.

8. 

Press and release the 1-cup and 2-cup button at the same time to store the value, the 1-cup and 2-cup LEDs blink 

rapidly 3 times.

9. 

If the “Intensity selection” is disabled (1-cup LED) has being selected in step 6, LED’s will switch off .

go to step 12

.

10.  If the “Intensity selection” is enabled (2-cup LED) has being selected the scale factor for the 60 ml setting need to be 

checked/adjusted.

Adjusting the scale factor for the strong/short cup volume (both cups).

11.  Depending if the volume has to de- or increase you have to push the one- or two-cup button.

Every time you push the 1- or 2-cup button, the LED will turn off  for 0.5 second (feedback to user) and the scale factor 

will be shortened or lengthened depending which button was pushed.

Pushing 1-cup button

, scale factor will be 

shorten

 approximately - 1 cc/ml (less coff ee)

Pushing 2-cup button

, scale factor will be 

lengthen

 approxi 1 cc/ml (more coff ee)

The new value will be stored when you press and release the 1-cup and 2-cup button at the same time, the 1-cup and 

2-cup LEDs blink rapidly 3 times.

12.  Turn appliance on again and brew one normal coff ee and check according specifi cation.

13.  Brew one strong coff ee cup by pressing the 1-cup button twice, measure the volume. 

14.  In case the volume is not within specifi cation repeat steps 1 – 11.

15. 

End of procedure.

Repair instruction

Summary of Contents for HD6596/50/G



















Reviews: