masking regions from motion detection
DUS704C Instruction Manual Rev H.docx
2
1. * WARNING * Do not touch the Pyro Sensor with your fingers. For indoor use only.
2. Select an appropriate indoor mounting location, as detailed in the location guidelines on the following
pages. Note that this product has three functions, and the optimum mounting location for each individual
function may conflict with each other, and may require the use of multiple sensors.
3. Remove the cover from the base unit by turning the cover in an anti clockwise direction.
4. Screw the base unit to the ceiling, passing the data cable through the cable entry hole.
5. Terminate the data cable as shown below.
6. Use silicon sealant to seal any cable entry and screw holes to prevent air draughts, dust and insects
from entering the enclosure.
7. Replace the cover onto the base unit by turning the cover in a clockwise direction.
connecting the data cable
motion detection mounting location
• Fix the sensor to a firm section of ceiling.
• Position the sensor so it is between 2.1 and 4.0 metres from the floor. Optimum height for the sensor is
2.4 metres.
• Position the sensor so it is at least 1 metre away from electrical lighting such as neon and fluorescent
lights.
• Position the sensor as to avoid exposing it to direct sunlight and heating/cooling sources.
• Keep data cables away from electrical wiring.
• Position the sensor where pedestrian traffic is more likely to walk across the detection “fingers” rather
than parallel with them (see Lens pattern diagram).
• Note that the coverage area is elliptical (see Motion Detector Coverage diagram) with the longest axis
being identified by the keyhole on the circuit board.
• For programming instructions refer to Dynalite Tech Note – Setting up Motion Detection functions.
INSTALLATI ON DETAIL S
DIMTEK 11 0
INPUT: 23 0 V 5 0-6 0Hz 10 A
O UTP UT: 1 x 230 V 10A
MOUNT VER TIC ALLY
AG AINST WALL
ENSUR E G OO D VENTILATIO N
FO LLO W INSTALLATION
INSTRUCTIO NS
Unit 6 -1 1 9 /1 3 3 McE VOY S t. A lex andria
NS W 20 1 5 A UST RA LIA
Manufactured by:
I SO LATE F RO M
M AI NS S UPP LY BE FO RE
RE M OV IN G TH IS C OV ER
NO US ER SE RV IC EA BLE PA RT S IN SI DE
SE RV IC E BY Q UA LIF IE D PE RSO NN EL O NLY
INSTALLATI ON DETAIL S
DIMTEK 11 0
INPUT: 23 0 V 5 0-6 0Hz 10 A
O UTP UT: 1 x 230 V 10A
MOUNT VER TIC ALLY
AG AINST WALL
ENSUR E G OO D VENTILATIO N
FO LLO W INSTALLATION
INSTRUCTIO NS
Unit 6 -1 1 9 /1 3 3 McE VOY S t. A lex andria
NS W 20 1 5 A UST RA LIA
Manufactured by:
I SO LATE F RO M
M AI NS S UPP LY BE FO RE
RE M OV IN G TH IS C OV ER
NO US ER SE RV IC EA BLE PA RT S IN SI DE
SE RV IC E BY Q UA LIF IE D PE RSO NN EL O NLY
Connect Data Cable in a "Daisy Chain"
serial cable permanent connectors
connect data cable in a “daisy chain”
Recommended Cable Colours
Green/White Pair
paralleled for GND
Orange/White Pair
paralleled for +VE
Blue/White Pair
Blue for DATA +
White for DATA-
Recommended Cable Types
Belden:
9503
Garland:
MCP3S
Hartland:
HCK603
M&M Cable:
B2003CS
Dynalite
DYNET-STP-CABLE
installation steps
