Philips AZ9003/19, Service Manual

Page: 10 / 22

SAA7324 – DECODER, DIGITAL SERVO IC AND D/A-CONVERTER CD10 (low voltage version)
Pin Name Direction Description
–––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
1 HFREF
→
CD10 comparator common mode input
2 HFIN
→
CD10 comparator signal input
3 ISLICE CD10
→
current feedback from data slicer
4 VSSA1 GND analog ground 1
5 VDDA1 +2.7 analog supply voltage 1
6 IREF CD10
→
reference current output pin
7 VRIN CD10
→
reference voltage for servo ADC’s
8 D1 HF-preamp
→
CD10 unipolar current input (central diode signal input)
9 D2 HF-preamp
→
CD10 unipolar current input (central diode signal input)
10 D3 HF-preamp
→
CD10 unipolar current input (central diode signal input)
11 D4 HF-preamp
→
CD10 unipolar current input (central diode signal input)
12 R1 HF-preamp
→
CD10 unipolar current input (satellite diode signal input)
13 R2 HF-preamp
→
CD10 unipolar current input (satellite diode signal input)
14 VSSA2 GND analog ground 2
15 CROUT CD10
→
X-TAL crystal/resonator output
16 CRIN X-TAL
→
CD10 crystal/resonator input
17 VDDA2 +2.7 analog supply voltage 2
18 LN CD10
→
DAC left channel differential output - negative
19 LP CD10
→
DAC left channel differential output - positive
20 VNEG
→
CD10 DAC negative reference input
21 VPOS
→
CD10 DAC positive reference input
22 RN CD10
→
DAC right channel differential output - negative
23 RP CD10
→
DAC right channel differential output - positive
24 SELPLL +2.7 selects whether internal clock multiplier PLL is used
25 TEST1 GND test control input 1; this pin should be tied low
26 CL16 CD10
→
16.9344 MHz system clock output
27 DATA CD10
→
NPC serial data output (3-state)
28 WCLK CD10
→
NPC word clock output (3-state)
29 SCLK CD10
→
NPC serial bit clock output (3-state)
30 EF CD10
→
C2 error flag output (3-state)
31 TEST2 GND test control input 2; this pin should be tied low
32 KILL CD10
→
HF-preamp kill output (programmable; open-drain)
33 VSSD1 GND digital ground 2
34 V2/V3 CD10
→
NPC versatile I/O: input versatile pin 2 or output versatile pin 3 (open-drain)
35 WCLI NPC
→
CD10 word clock input (for data loopback to DAC)
36 SDI NPC
→
CD10 serial data input (for data loopback to DAC)
37 SCLI NPC
→
CD10 serial bit clock input (for data loopback to DAC)
38 RESETn µP
→
CD10 power-on reset input (active low)
39 SDA µP
↔
CD10 microcontroller interface data I/O line (open-drain output)
40 SCL µP
→
CD10 microcontroller interface clock line input
41 RAB µP
→
CD10 microcontroller interface R/W and load control line input (4-wire bus mode)
42 SILD µP
→
CD10 microcontroller interface R/W and load control line input (4-wire bus mode)
43 STATUS CD10
→
servo interrupt request line/decoder status register output (open-drain)
44 TEST3 GND test control input 3; this pin should be tied low
45 RCK
→
CD10 subcode clock input
46 SUB CD10
→
P-to-W subcode bits output (3-state)
47 SFSY CD10
→
µP subcode frame sync output (3-state)
48 SBSY CD10
→
NPC subcode block sync output (3-state)
49 CL11/4 CD10
→
11.2896 MHz or 4.2336 MHz (for microcontroller) clock output
50 VSSD2 GND digital ground 3
51 DOBM CD10
→
bi-phase mark output (externally buffered; 3-state)
52 VDDD1P +2.7 digital supply voltage 2 for periphery
53 CFLG CD10
→
correction flag output (open-drain)
54 RA CD10
→
servo driver radial actuator output
55 FO CD10
→
servo driver focus actuator output
56 SL CD10
→
servo driver slide control output
57 VDDD2C +2.7 digital supply voltage 3 for core
58 VSSD3 GND digital ground 4
59 MOTO1 CD10
→
servo driver motor output 1; versatile (3-state)
60 MOTO2 CD10
→
motor output 2; versatile (3-state)
61 V4 CD10
→
HF-EQ switch versatile output pin 4
62 V5 CD10
→
HF-GAIN switch versatile output pin 5
63 V1 innerswitch
→
CD10 versatile input pin 1
64 LDON CD10
→
HF-preamp laser drive on output (open-drain)
3-2
CS 46 667