Alignments
EN 37
Q549.2E LA
6.
2009-May-08
•
Set the RED, GREEN and BLUE default values according
to the values in
Table 6-2
.
•
When finished press OK on the RC, then press STORE (in
the SAM root menu) to store the aligned values to the NVM.
•
Restore the initial picture settings after the alignments.
Table 6-2 White tone default setting
6.4
Option Settings
6.4.1
Introduction
The microprocessor communicates with a large number of I2C
ICs in the set. To ensure good communication and to make
digital diagnosis possible, the microprocessor has to know
which ICs to address. The presence / absence of these
PNX5100 ICs (back-end advanced video picture improvement
IC which offers motion estimation and compensation features
(commercially called HDNM) plus integrated Ambilight control)
is made known by the option codes.
Notes:
•
After changing the option(s), save them by pressing the OK
button on the RC before the cursor is moved to the left,
select STORE in the SAM root menu and press OK on the
RC.
•
The new option setting is only active after the TV is
switched “off” / “stand-by” and “on” again with the mains
switch (the NVM is then read again).
6.4.2
Dealer Options
For dealer options, in SAM select “Dealer options”.
See Table
6-4 SAM mode overview
.
6.4.3
(Service) Options
Select the sub menu's to set the initialisation codes (options) of
the model number via text menus.
See Table
6-4 SAM mode overview
.
6.4.4
Opt. No. (Option numbers)
Select this sub menu to set all options at once (expressed in
two long strings of numbers).
An option number (or “option byte”) represents a number of
different options. When you change these numbers directly,
you can set all options very quickly. All options are controlled
via eight option numbers.
When the NVM is replaced, all options will require resetting. To
be certain that the factory settings are reproduced exactly, you
must set both option number lines. You can find the correct
option numbers on a sticker inside the TV set and in Table
6-3
Option and display code overview
.
Example:
The options sticker gives the following option
numbers:
•
08192 00133 01387 45160
•
12232 04256 00164 00000
The first line (group 1) indicates hardware options 1 to 4, the
second line (group 2) indicate software options 5 to 8.
Every 5-digit number represents 16 bits (so the maximum value
will be 65536 if all options are set).
When all the correct options are set, the sum of the decimal
values of each Option Byte (OB) will give the option number.
See Table
6-3 Option and display code overview
for the
options.
Diversity
Not all sets with the same Commercial Type Number (CTN)
necessarily have the same option code!
Use of Alternative BOM => an alternative BOM number usually
indicates the use of an alternative display or power supply. This
results in another display code thus in another Option code. For
the power supply there is no difference. Refer to Chapter
2.
Technical Specifications and, Connections
.
6.4.5
Option Code Overview
Table 6-3 Option and display code overview
Important:
after having edited the option numbers as
described above, you
must press OK
on the remote control
before the cursor is moved to the left
!
6.5
Reset of Repaired SSB
A very important issue towards a repaired SSB from a service
repair shop implies the reset of the NVM on the SSB.
A repaired SSB in service should get the service Set type
“00PF0000000000” and Production code “00000000000000”.
Also the virgin bit is to be set. To set all this, you can use the
ComPair tool.
In case of a display replacement, reset the “Operation hours
display” to “0”, or to the operation hours of the replacement
display.
New here in this chassis is the “Net TV” functionality. Therefore
the CTN (“set type” item in CSM1) must be filled into the spare
SSB to ensure access to the Net TV portals.
The loading of the CTN can be done via ComPair (Model
number programming).
The reset item (Clear NET TV memory) can be selected via
MENU (or HOME) => Setup => Installation => Clear NET TV
memory (customer preferences stored at provider side will be
reset now).
White Tone
32"
37"
Black level
offset
Colour Temp
R
G
B
R
G
B
R
G
Normal
127
95
97
127
121
106
8
8
Cool
127
100
112
124
127
119
8
8
Warm
127
89
52
127
111
64
8
8
White Tone
56"
Black level
offset
Colour Temp
R
G
B
R
G
Normal
127
117
111
8
8
Cool
124
124
125
8
8
Warm
127
95
65
8
8
CTN
Options Group 1
Options Group 2
Disp.
code
32PFL9604H/12 08211 35971 18431 45288 30645 47282 00184 00000 181
32PFL9604H/60 08211 35971 18431 45288 30645 47282 00184 00000 181
37PFL9604H/12 08227 35972 18431 45288 30625 47282 00176 00000 161
37PFL9604H/60 08227 35972 18431 45288 30625 47282 00176 00000 161
56PFL9954H/12 08275 33925 18431 45288 30644 47282 00161 00000 180
