Philips 221TE2LB/00 Service Manual Download Page 97

Page: 97 / 119

Page 34 of 45

221TE2L LCD

General Product Specification

5 Non functional requirements

5.1

DEFAULT AND INITIAL CONTROL VALUES

Initial value: Settings when the set turns on from standby.
Default value: Out of box settings.
Factory reset to default: Settings when “Factory Reset” in menu is selected.

Control

Initial Value

Default Value

Factory
Reset to
Default

Smart
settings

Last status

Home: Standard

Yes (Personal
settings back to
default too)

Volume Last

status

Yes

AVL

Last status

Off

Yes

Incredible
Surround

Last status

Off

Yes

Dual I/II (EU)

Last status per
channel

Stereo

Forced Mono
(EU)

Last status per
channel

Off

Audio

User mute

Last status

Off

Yes

PC Brightness

Last status

100

Yes

PC Contrast

Last status

Yes

PC Color
Temp.

Last status

Cool

Yes

PC picture
format

Last status

Full Screen

Yes

PC Picture
Manual adj.
Phase
Clock
Horizontal
Vertical

Last status

TBD

Yes

DNR/NR Last

status

Yes

Video

TV/AV Picture
format

4:3 : user setting.
Wide screen : WSS
or user setting.

4:3 : for 4:3 sets
Widescreen : for 16:9
sets

Yes

Source
selection

Selected
source

Last status

Program

Last status

Lowest program

Lock

Lock Last

status Off

Summary of Contents for 221TE2LB/00
























































































































Search results

Summary of Contents for 221TE2LB/00

Reviews:

Brands by name

Popular brands

Philips 221TE2LB/00, Service Manual

Search results

Summary of Contents for 221TE2LB/00

Reviews:

Brands by name

Popular brands