background image

5

Using other menus

To adjust a menu:

æ

Display the menu.

Â

Select a setting.

ê

Adjust.

Note: the menus disappear automatically after 30 seconds if no further adjustments are made.
To exit from the menus, press 

(or 

to come back to the previous stage).

Adjusting the sound

You can store your own sound and picture settings.

æ

First carry out your menu settings.

Â

Next, select 

PERSONAL

and press 

.The message 

STORED

is displayed.

The settings are stored.

Values are saved under PERSONAL in the Smart sound and picture controls 
(

and 

)

Note: volume and DELTA VOL. are automatically stored and do not need to be stored
in the PERSONAL menu.

Press 

.You can adjust:

BRIGHTNESS

,

COLOUR

,

CONTRAST

,

SHARPNESS

,

TINT

,

C

and 

NOISE RED.

.

• SHARPNESS: alters the crispness of the image,

• TINT: alters the colour balance.There are 3 options: COLD (blue tint), NORMAL

(balanced) or WARM (red tint).

• C: automatically adjusts the image contrast according to content 

(the darkest part of the image is always black).

• NOISE RED.: alleviates fuzziness (snowy picture).This setting is useful when

reception is difficult.

Press 

.You can adjust 

DELTA VOL.

• DELTA VOLUME (volume difference): allows you to compensate for the volume

differences between the different programmes or the EXT sockets.This setting is
available for programmes 1 - 40 and the EXT sockets.

Adjusting the picture

Storing settings

Summary of Contents for 14PT1354/58









Reviews: