background image

Limited Warranty

Philio Technology Corporation  product  is  warranted against defects in

material and workmanship for two years.  Philio Technology Corporation

will  replace  it   free   of  charge  and   does  not  issue  any  refunds.  This

warranty extends only to wholesale customers who buy through Philio

Technology   Corporation   authorized   distribution   channels.   Philio

Technology Corporation does not warrant this product to consumers. 

This warranty does not apply to: 

(a) damage to units caused by accident, dropping or abuse in handling,

or any negligent use.

(b) units which have been subject to unauthorized repair, taken apart,

or otherwise modified.

(c) units not used in accordance with instruction.

(d) damages exceeding the cost of the product.

(e)   transit   damage,   initial   installation   costs,   removal   cost,   or  re-

installation cost. 

FCC Interference Statement 

This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and  used

in accordance with the instructions,  may cause  harmful interference to

radio   communications.         However,     there   is   no   guarantee   that

interference will not occur in a particular installation.  If this equipment

does cause harmful  interference to radio or television reception,  which

can be  determined by turning the equipment off and on,  the user  is

encouraged to try to correct the interference by one of the following

measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

Consult   the   dealer   or   an   experienced   radio/TV   technician   for

help.

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions: 

(1) This device may not cause harmful interference, and

(2)   This   device   must   accept   any   interference   received,   including

interference that may cause undesired operation. 

 

FCC Caution: Any changes or modifications not expressly approved by

the party responsible for compliance could void the user's authority to

operate this equipment. 

 

This transmitter  must not  be co-located  or operating  in conjunction

with any other antenna or transmitter.

Warning

Do not dispose of electrical appliances as unsorted municipal waste,

use   separate   collection   facilities.   Contact   your   local   government   for

information   regarding   the   collection   systems   available.   If   electrical

appliances are disposed of in landfills or dumps, hazardous substances

can leak into the groundwater and get into the food chain, damaging

your health and well-being.

When replacing old appliances with new once, the retailer is legally

obligated to take back your old appliance for disposal at least for free

of charge.

10

Summary of Contents for PSM02











Reviews: