Philio PSE04 Quick Start Manual Download Page 1

Multiple Sound Siren PSE04

Built-in high accuracy Temperature sensor

The PSE04 is a wireless siren, based on Z-Wave

TM

 technology. It is the

Z-Wave Plus

TM

  product, it support the security, OTA... Those newest

features   of   the  Z-Wave

TM

  technology.  Z-Wave

TM

  is   a   wireless

communication protocol designed for home automation, specifically to

remotely   control   applications   in   residential   and   light   commercial

environments. The technology uses a low-power RF radio embedded or

retrofitted into home electronics devices and systems, such as lighting,

home access control, entertainment systems and household appliances.

This product can be included and operated in any Z-Wave

TM

  network

with other Z-Wave

TM

 certified devices from other manufacturers and/or

other applications.  All non-battery operated nodes within the network

will act as repeaters regardless of vendor to increase reliability of the

network. 

The device adopt the Z-Wave

TM

  700 series chip, when your Z-Wave

TM

network   system   is   all   made   by   Z-Wave

TM

  700   series   devices.   The

network system will have the advantages as below.

Concurrent multi-channel support reduces external interference.

Better RF range, improve about 10 meters in indoor.

Support 100 Kbps transmit speed, speed up communication.

Specification

Rating

6VDC (AA Battery *4) 

RF distance

Min. 40M indoor,

100M outdoor line of sight,

RF Frequency

868.40 MHz, 869.85 MHz(EU)

908.40 MHz, 916.00 MHz(US)

920.9MHz, 921.7MHz, 923.1MHz

(TW/KR/Thai/SG)

921.40 MHz, 919.80 MHz(ANZ)

869.00 MHz(RU)

865.20 MHz(IN)

916.00 MHz(IL)

RF Maximum Power 

+10dBm (Peak), -10dBm 

(Average)

Dimension

170mm(L) X 48mm (W) X 30(H)

Weight

205g

IP classification

IP44; Outdoor use

Operation temperature

-20 to 55° C

Humidity

85%RH max

FCC ID

RHHPSE04

Marking

CE/NCC

1

Summary of Contents for PSE04










Reviews: