manualshive.com logo in svg

Philio PAT05, Manual, Page: 5 / 7

Share
Download
Philio PAT05 Manual Download Page 5

NO

.

Name

Def.

Valid

Description

14

ECO2 Auto 
Report Time

1

1 ~ 127

The interval time for auto report the eCO2.
The default value is 1. The tick time can 
setting by the configuration No.16.

15

TVOC Auto 
Report Time

1

1 ~ 127

The interval time for auto report the 
TVOC.
The default value is 1. The tick time can 
setting by the configuration No.16.

16

Auto Report 
Tick Interval

60

1 ~ 127

The interval time for auto report each tick. 
Setting this configuration will effect 
configuration No.14 and No.15.
The unit is 1 minute.
Caution1: The value is unsigned byte, the 
range is from 0x00 ~ 0x7F.

17

eCO2 
Differential 
percent Report

10

1~100%

The eCO2 Differential to report.
0 means turn off this function.
The unit is percentage.
Enable this function the device will detect 
every percentage.
And when the lightSensor is over 10 
percentage, it will continue report.

18

TVOC 
Differential 
percent Report

10

1~100%

The TVOC  Differential to report.
0 means turn off this function.
The unit is percentage.
Enable this function the device will detect 
every percentage.
And when the lightSensor is over 10 
percentage, it will continue report.

Z-Wave Supported Command Class

Command Class

Version

Required Security Class

Z-Wave Plus Info

2

None

Version

3

Highest granted Security Class

Manufacturer Specific

2

Highest granted Security Class

Security 2

1

None

Device Reset Locally

1

Highest granted Security Class

Association

2

Highest granted Security Class

Association Group Information

1

Highest granted Security Class

Powerlevel

1

Highest granted Security Class

Configuration

1

Highest granted Security Class

Notification

8

Highest granted Security Class

Firmware Update Meta Data

4

Highest granted Security Class

Supervision

1

None

Transport Service

2

None

Sensor multilevel

11

Highest granted Security Class

Over The Air (OTA) Firmware Update

The device supports Z-Wave firmware update via OTA.
Before starting the update, please remove the front case of the device otherwise the
hardware check will fail.
Let the controller into firmware update mode, and press the front tamper key once to
start the update.
After firmware download is completed, the LED light will flash intermittently.

Overview

5

Summary of Contents for PAT05








Reviews:

No comments