Phil & Teds alpha Series Manual For Future Reference Download Page 15 | Manualshive

Page: 15 / 44

background image

Safety Warnings

Checklist Before Use

Inspect

•

Only use this infant car seat rear facing

• Infant car seat is free of damage

Verify Child within Weight and Size Range

•

Weight between 4–35lbs/1.8–15.9kg

• Height 81cm / 32inches or less.

Secure Child Properly in Infant Car Seat

•

Correct shoulder strap height (at or slightly

  below shoulders)
•   Harness not twisted and low across hips
•   Harness secure and tight

Install Infant Car Seat Rearward-facing in Safe
Location in Vehicle

•

Vehicle seats that face front of vehicle only

•   Handle locked in specified position (2a)
•   Child facing rear of vehicle
•   Position with NO active airbag
•   3 point (shoulder/lap) belt used
•   Seat belt not twisted
•   Belt path followed
•   Tight against vehicle seat

«
...
13
14
15
16
17
...
»

Summary of Contents for alpha Series













































Reviews:

No comments

Related manuals for alpha Series

Brand: JANE Pages: 40

Evolution BS01-B

Brand: Phil & Teds Pages: 26

Brand: Kinderkraft Pages: 188

Brand: CYBEX Pages: 10

Brand: CYBEX Pages: 61

Alpha Omega All in One

Brand: DJG Pages: 30

Brand: GB Pages: 103

Brand: Safety 1st Pages: 32

Brand: Toco Pages: 24

Brand: Klippan Pages: 40

Brand: Klippan Pages: 44

Brand: Klippan Pages: 52

Highrise/AmbassadorBelt-Positioning Booster

Brand: Dorel Juvenile Group Pages: 13

Brand: Dorel Juvenile Group Pages: 16

Brand: Dorel Juvenile Group Pages: 18

Brand: Dorel Juvenile Group Pages: 26

Brand: Dorel Juvenile Group Pages: 30

ALPHA OMEGA ELITE 4358-3340A

Brand: Dorel Juvenile Group Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands