PHICOMM FD-221 User Manual Download

Page: 4 / 61

Table of Contents

ADSL2/2+ Modem Router

www.phicomm.com

............................................................................................................................................ 31

VLAN

......................................................................................................................................... 33

ADSL

......................................................................................................................................... 35

Access Management

...................................................................................... 35

ACL

............................................................................................................................................ 36

Filter

.......................................................................................................................................... 37

SNMP

........................................................................................................................................ 38

UPnP

......................................................................................................................................... 38

DDNS

........................................................................................................................................ 39

CWMP

....................................................................................................................................... 40

Maintenance

...................................................................................................... 40

Administration

...................................................................................................................... 41

Time Zone

............................................................................................................................... 41

Firmware

................................................................................................................................. 43

SysRestart

............................................................................................................................... 44

Diagnostics

............................................................................................................................. 45

Status

.................................................................................................................... 45

Device Info

............................................................................................................................. 46

System Log

............................................................................................................................. 47

Statistics

.................................................................................................................................. 47

Help

....................................................................................................................... 48

Summary of Contents for FD-221





























































Search results

Summary of Contents for FD-221

Reviews:

Related manuals for FD-221

Brands by name

Popular brands

PHICOMM FD-221, User Manual

Search results

Summary of Contents for FD-221

Reviews:

Related manuals for FD-221

Brands by name

Popular brands