background image

PFT RITMO

 

powercoat 110V

 Operating Instructions 

Last updated 12.2006 

Knauf PFT GmbH & Co. KG  

27 

 

Fault Cause 

Remedy 

Machine does not start via 
wireless remote control. 

Insufficient pressure gradient in 
remote control due to blocked air 
pipe or air nozzle tube. 

Check if air pipe is blocked. 
Clean air nozzle tube. 

Machine does not start. 

Too much hardened material in 
hopper or mixing area. 

WARNING! 
Turn off main switch and pull 
out plug first. 
Half-empty hopper and restart 
or clean entire hopper and 
mixing area. 

Machine does not start. 

Hardened material is blocking the 
rotor/stator pump unit. 

WARNING! 
Turn off main switch and pull 
out plug first. 
Remove pump and install new 
pump. 

No material flow. 

Bad mixture in mixing tube. 

Add more water. 

Deviations in filler 
consistency (material flow 
“thin-thick”). 

Material clogs, narrowing the 
mixing tube inlet. The mixing shaft 
or pump might be worn out. 

Clean mixing shaft, mixing area 
and pressure flange. Inspect 
mixing shaft and pump 
components. Replace if 
necessary. 

Deviations in filler 
consistency (mortar flow 
“thin-thick”). 

Pressure reducing valve 
misadjusted or defective. 

Increase water supply by 10 % 
for approx. ½ minute and then 
turn back slowly. Reset 
pressure reducing valve to 
factory setting. 

Water level rises in mixing 
tube during operation.  

Backpressure in material hose 
higher than pump pressure. 

Check spray gun or material 
hose for blockages and clean. 
Warning! Wear protective 
clothing, goggles etc. 

 
 
 
 
 
 

Summary of Contents for PFT RITMO

















































Reviews: