Perle RPS1620 User Manual Download Page 65

Page: 65 / 72

Apx-5

Appendices

C.3. Perle Support Centres Worldwide

Notes:

• Perle offers free technical support to Perle Authorised Distributors

and Registered Perle Resellers.

• To access technical support please visit the Perle website at www.

perle.com/support.

• If you are unable to ﬁnd the information you require, please feel free

to contact our technical support teams by email using the addresses

shown in the next table.

Region

Address

North America

Perle Systems Ltd.

60 Renfrew Drive

Markham

Ontario

Canada

L3R OE1

Email: [email protected]

Europe

Perle Systems Europe Ltd.

3 Wintersells Road

Byﬂeet Surrey

KT14 7LF

Email: [email protected]

Asia

Perle Asia Paciﬁc (Pte) Ltd.

Yu Li Industrial Building

No 37 Lor 23 Sims Avenue

04-01/05

Singapore 388371

Email: [email protected]

Worldwide

Perle Systems Ltd.

60 Renfrew Drive

Markham

Ontario

Canada

L3R OE1

Email: [email protected]

Summary of Contents for RPS1620









































































Search results

Summary of Contents for RPS1620

Reviews:

Related manuals for RPS1620

Brands by name

Popular brands

Perle RPS1620, User Manual

Search results

Summary of Contents for RPS1620

Reviews:

Related manuals for RPS1620

Brands by name

Popular brands