Perle RPS1620 User Manual Download Page 8

Page: 8 / 72

1-2

RPS Series: Remote Power Switches - User's Guide

Four Different RPS Models

This User’s Guide discusses four different RPS models. Throughout this

User’s Guide, all four units are referred to as the "RPS". Aside from the

hardware conﬁguration, all other features function identically in both units

except where noted.
The table below summarizes the four RPS units covered in this manual:

•

RPS820:

Horizontal mount. Eight (8) switched, 208 to 240 VAC,

IEC-320-C13 outlets. 20 Amps maximum total load.

One (1) Rack Unit.

•

RPS830:

Horizontal mount. Eight (8) switched, 100 to 120 VAC,

NEMA 5-15R outlets. 30 Amps maximum total load.

One (1) Rack Unit.

•

RPS1620:

Vertical mount. Sixteen (16) switched, 208 to 240 VAC,

IEC-320-C13 outlets. 20 Amps maximum total load.

Zero (0) Rack Unit.

•

RPS1630:

Vertical mount. Sixteen (16) switched, 100 to 120 VAC,

NEMA 5-15R outlets. 30 Amps maximum total load.

Zero (0) Rack Unit.

Typographic Conventions

Throughout this manual, typefaces and characters have been used to denote the

following:

COURIER FONT

Indicates characters typed on the keyboard.

For example,

/ON 3

/OFF 5

[Bold Font]

Text set in bold face and enclosed in square brackets

indicates a speciﬁc key.

For example,

[Enter]

[Esc]

Summary of Contents for RPS1620









































































Search results

Summary of Contents for RPS1620

Reviews:

Related manuals for RPS1620

Brands by name

Popular brands

Perle RPS1620, User Manual

Search results

Summary of Contents for RPS1620

Reviews:

Related manuals for RPS1620

Brands by name

Popular brands