Perkins 403C-11 Workshop Manual Download Page 68 | Manualshive

Page: 68 / 128

Perkins 403C-11 Workshop Manual Download Page 68

6

58

Workshop Manual, TPD 1458E, issue 3 - Perkins Confidential: Green

400 Series

Maximum fuel screw and maximum speed screw

Location

Operation 6-8

Caution: The fuel adjustment setscrew must be set correctly for the engine to comply with emissions
legislation. This must only be carried out by an approved Perkins distributor.

Notes:

l

The maximum fuel setscrew (1) and the maximum speed setscrew (2) must not be adjusted by the
operator.

l

Under certain circumstances it may be necessary to remove the anti tamper device for the maximum fuel
setscrew. This must only be carried out by an approved Perkins distributor.

l

Any adjustment to the maximum fuel screw will require an engine test brake, and also a check of maximum
no load speed to confirm the settings.

Engine

Torque Nm (lbf ft) kgf m

All models

Maximum fuel screw lock nut

14 (10.3) 1,4

Maximum speed screw lock nut

14 (10.3) 1,4

1

2

3

H1075

«
...
66
67
68
69
70
...
»

Summary of Contents for 403C-11

































































































































Reviews:

No comments