Perkins 1106C Genset Troubleshooting Manual Download Page 96

Page: 96 / 188

KENR6933

Troubleshooting Section

i02527064

CID 1834 FMI 02

Conditions Which Generate This Code:

The Electronic Control Module (ECM) detects the

following condition:

The signal from the keyswitch was erratic because

the keyswitch was cycled at least three times within

the last second.

Note:

This code can be generated by rapidly

cycling the keyswitch. Some control modules on

the application may require this action in order to

prompt

ash codes. If this occurs, clear the logged

diagnostic codes in order to prevent future confusion

or an incorrect diagnosis.

System Response:

The ECM will log the diagnostic code and the warning

lamp will come on while this diagnostic code is active.

The ECM will stop energizing the injector solenoids

and the engine will shut down.

Possible Performance Effect:

Engine shutdown

Troubleshooting:

Perform the following diagnostic procedure: “Ignition

Keyswitch Circuit and Battery Supply Circuit - Test”

Results:

•

OK – STOP.

i02527065

CID 2246 FMI 06

Conditions Which Generate This Code:

The Electronic Control Module (ECM) has detected a

high current condition (short circuit) after attempting

to activate the glow plug starting aid.

The ECM detects the following conditions:

•

The engine is not cranking.

•

The ECM has been powered for at least 1 second.

•

There is a high current condition (short circuit) for

more than 2 seconds.

System Response:

The ECM will log the code. An ECM that was

previously blank will require a total of 2 hours of

operation before the diagnostic code will be logged. If

equipped, the warning light will come on. The ECM is

unable to activate the relay for the glow plug starting

aid. The glow plugs will not operate or the glow plugs

will operate all the time.

Possible Performance Effect:

The engine may be dif

cult to start in cold

temperatures and the exhaust may emit white smoke.

Troubleshooting:

Perform the following diagnostic procedure: “Starting

Aid (Glow Plug) Relay Circuit - Test”

Results:

•

OK – STOP.

Summary of Contents for 1106C Genset




























































































































































































Search results

Summary of Contents for 1106C Genset

Reviews:

Perkins 1106C Genset, Troubleshooting Manual, Page: 96 / 188

Search results

Summary of Contents for 1106C Genset

Reviews: