Perkins 1106C Genset Troubleshooting Manual Download Page 131

Page: 131 / 188

KENR6933

131

Troubleshooting Section

Expected Result:

The short circuit diagnostic code is not present when

a new sensor is connected.

Results:

•

OK – Use the electronic service tool in order to

clear all logged diagnostic codes and then verify

that the repair eliminates the fault. STOP.

•

Not OK – Repair the engine harness connector.

Use the electronic service tool to clear the logged

diagnostic codes. STOP.

Test Step 7. Create a Short Circuit

Between the Signal and the Common

Terminals at the Engine Harness

Connector

Turn the keyswitch to the ON position.

Fabricate a jumper wire 150 mm (6 inch) long.

Crimp a terminal to both ends of the wire.

Monitor the “Active Diagnostic Code” screen on

the electronic service tool before installing the

jumper wire and after installing the jumper wire.

Install the jumper on the engine harness

connector. Install one end of the jumper at the

sensor signal (terminal 3). Install the other end

of the jumper at the common connection for

the pressure sensor (terminal 2). Wait at least

30 seconds for activation of the short circuit

diagnostic code.

Expected Result:

A short circuit diagnostic code is active when the

jumper is installed. An open circuit diagnostic code is

active when the jumper is removed.

Results:

•

OK – The engine harness and the ECM are OK.

Repair:

Perform the following repair:

Temporarily connect the suspect sensor.

Use the electronic service tool to verify if the

diagnostic code remains active.

If the diagnostic code is active replace the

sensor.

Use the electronic service tool in order to clear

all logged diagnostic codes and then verify that

the repair eliminated the fault.

STOP.

•

Not OK – The open circuit diagnostic code

remains active when the jumper is installed. The

most probable location for the open circuit is in the

common wire for the sensor, or in the sensor signal

wire of the engine harness between the ECM and

the sensor. Remove the jumper. Proceed to Test

Step 8.

Test Step 8. Check the Operation of the

ECM by Creating Open and Short Circuits

at the ECM Connector

Turn the keyswitch to the OFF position.

Disconnect connector P2 from the ECM.

Thoroughly inspect both halves of the connector

for signs of corrosion or moisture. Refer to

Troubleshooting, “Electrical Connectors - Inspect”.

Reconnect P2 connector.

Turn the keyswitch to the ON position. Use the

electronic service tool in order to monitor the

“Active Diagnostic Code” screen. Wait at least 10

seconds for activation of the code.

An open circuit diagnostic code should be active

for the suspect sensor.

Note:

When the P2connector is disconnected, all of

the open circuit diagnostic codes for the pressure

sensors and temperature sensors will be active. This

is normal. Disregard the diagnostic codes for the

pressure sensors and the temperature sensors that

are not suspect. Monitor the diagnostic codes for the

suspect sensors only.

Turn the keyswitch to the OFF position.

Fabricate a jumper wire 150 mm (6 inch) long.

Crimp a terminal to both ends of the wire.

Install the jumper wire on the P2 connector.

Insert the jumper wire between the terminal

for the suspect sensor signal and the common

connection for the engine’s pressure sensor.

Use the electronic service tool to verify that there

is a “Voltage Above Normal” diagnostic code.

Expected Result:

“Voltage Below Normal” diagnostic codes and

“Voltage Above Normal” diagnostic codes were

active.

Results:

•

OK – The ECM is operating correctly. Proceed to

Test Step 9.

Summary of Contents for 1106C Genset




























































































































































































Search results

Summary of Contents for 1106C Genset

Reviews:

Perkins 1106C Genset, Troubleshooting Manual, Page: 131 / 188

Search results

Summary of Contents for 1106C Genset

Reviews: