Perkins 1106C Genset Troubleshooting Manual Download Page 173

Page: 173 / 188

KENR6933

173

Troubleshooting Section

Repair:

Perform the following repair:

Repair the connectors or the harness and/or

replace the connectors or the harness. Ensure that

all of the seals are correctly in place and ensure

that the connectors are completely coupled.

Verify that the repair eliminates the fault.

STOP.

Test Step 2. Check for Active Diagnostic

Codes

Connect Perkins EST to the data link connector.

Turn the keyswitch to the ON position.

Monitor the active diagnostic code screen on

Perkins EST. Check and record active diagnostic

codes.

Expected Result:

Result 1

Diagnostic code 91-08 is active.

Result 2

There are no active diagnostic codes that

are associated with the speed demand circuit at this

time. However, a fault is suspected.

Results:

•

Result 1

–

Proceed to Test Step 3.

•

Result 2 – There may be an intermittent connection

in the wiring. Proceed to Test Step 3.

Test Step 3. Check the Control Signal.

Refer to the OEM supplied manual for the control

system.

Check that the output signal from the control

system is correct.

Expected Result:

The output signal from the control system should be

within the speci

cation in the OEM supplied manual.

Results:

•

–

The output signal from the control system is

correct. Proceed to Test Step 4.

•

Not OK – The output signal from the control

system is not correct or the control system is

incorrectly con

gured.

Repair:

Repair the control system or con

gure the

control system. Refer to the OEM supplied manual.

Verify that the repair eliminates the fault.

STOP.

Test Step 4. Check the Signal at the ECM.

Turn the keyswitch to the OFF position.

Remove the P1 OEM connector.

Temporarily remove the pin from P1:53.

Reconnect P1 OEM connector.

Connect the red probe of a multimeter to the

removed pin and the black probe of a multimeter

to P1:33.

Turn the keyswitch to the ON position.

Check that the signal at the ECM is the same

value as the output signal from the control system.

Turn the keyswitch to the OFF position.

Remove P1 OEM connector and reinstall P1:53 to

the P1 OEM connector.

Reconnect P1 OEM connector.

Expected Result:

The signal at the ECM is the same value as the

output signal from the control system.

Results:

•

OK – The terminals on the ECM have the correct

voltage for the control system.

Repair:

The ECM is suspect.

Temporarily connect a test ECM.

Note:

The test ECM should be programmed with the

correct software. All parameters should be set to the

same value as the suspected ECM.

If the fault is eliminated with the test ECM,

install the suspect ECM and verify that the fault

returns.

If the fault returns replace the ECM.

STOP.

•

Not OK – There is a fault in the harness or the

connectors between the sensor and the ECM.

Check all of the connections between the ECM and

the control system. Repair the damaged cables

or replace the damaged cables. Check that the

repairs have eliminated the fault. STOP.

Summary of Contents for 1106C Genset




























































































































































































Search results

Summary of Contents for 1106C Genset

Reviews:

Perkins 1106C Genset, Troubleshooting Manual, Page: 173 / 188

Search results

Summary of Contents for 1106C Genset

Reviews: