manualshive.com logo in svg

PerkinElmer Frontier FT-IR, User Manual

Share
Download
PerkinElmer Frontier FT-IR User Manual Download Page 61

Routine Maintenance . 61 

1.

 

The tubing is connected to the instrument by a universal pipe fitting which is secured to 

the tubing with a nut. Two sets of fittings are supplied with the instrument. Assemble 

the fittings to the tubing as illustrated in Figure 29. 

 

Figure 29 Purge fittings 

2.

 

Tighten the nut, ensuring it is not over tightened. 

3.

 

Push the connector on the end of the tubing into the purge connector of the 

compartment to be purged (Figure 30). 
If the connector will not push in, press the clip at the bottom of the port and try again. 

 

Figure 30 Connector fitted to purge port 

4.

 

Connect the free end of the tubing to the gas regulator. 

NOTE: 

Ensure the regulator is set to a pressure not greater than 6.9 kPa (1 lbf/in

2

). 

5.

 

Open the gas flow valve on the regulator until a flow rate of 28 l/minute (1 ft

3

/minute) 

is achieved. 
The instrument compartment is purged in 10 minutes. The sample compartment is 

purged in 2 minutes. 

6.

 

Once purging is complete turn off the gas supply. 

Instrument purge 

Sample purge 

Beveled end of 

connector 

Knurled nut 

Tubing 

Summary of Contents for Frontier FT-IR





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands