3
IMPORTANT SAFETY INSTRUCTIONS
NOTE:
The power supply cord with this air
conditioner contains a current detection
device designed to reduce the risk
of fire. Please refer to the section
“Operation of Current Device” (below)
for details. In the event that the power
supply cord is damaged, it cannot be
repaired. It must be replaced by an
authorized repair technician with a cord
from the Product Manufacturer.
WARNING
Avoid fire hazards or electric shock.
DO NOT
use an extension cord or an
adapter plug.
DO NOT
remove any prong
from the power cord.
OPERATION OF
CURRENT DEVICE:
The power supply cord contains a
current device that senses damage
to the power cord. To test your power
supply cord, do the following:
1. Plug in the air conditioner.
2. The power supply cord will have
TWO buttons on the plug head. Press
the TEST button. You will notice a
click as the RESET button pops out.
3. Press the RESET button. Again,
you will notice a click as the button
engages.
4. The power supply cord is now
supplying electricity to the unit. (On
some products this is also indicated
by a light on the plug head.)
WARNING
FOR YOUR SAFETY: Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other appliances.
WARNING - PREVENT ACCIDENTS
To reduce the risk of fire, electrical shock, or injury to persons when using
your air conditioner, follow basic precautions, including the following:
● Be sure the electrical service is adequate for the model you have
chosen. This information can be found on the serial plate, which is
located on the side of the cabinet and behind the grille.
● If the air conditioner is to be installed in a window, you will probably
want to clean both sides of the glass first. If the window is a triple-
track type with a screen panel included, remove the screen completely
before installation.
● Be sure the air conditioner has been securely and correctly installed
according to the installation instructions in this manual.
● Save this manual for possible future use in removing or installing this unit.
● When handling the air conditioner, be careful to avoid cuts from sharp
metal fins on front and rear coils.
WARNING - ELECTRICAL INFORMATION
The complete electrical rating of your new room air conditioner is
stated on the serial plate. Refer to the rating when checking the
electrical requirements.
● Be sure the air conditioner is properly grounded. To minimize shock
and fire hazards, proper grounding is important. The power cord is
equipped with a three-prong grounding plug for protection against
shock hazards.
● Your air conditioner must be used in a properly grounded wall
receptacle. If the wall receptacle you intend to use is not adequately
grounded or protected by a time delay fuse or circuit breaker, have a
qualified electrician install the proper receptacle.
● Ensure the receptacle is accessible after the unit installation.
●
DO NOT
run air conditioner without side protective cover in place. This
could result in mechanical damage within the air conditioner.
●
DO NOT
use an extension cord or an adapter plug.
NOTE:
DO NOT
use the plug to turn the unit on or off.
● Always make sure the RESET button is pushed in for correct operation.
● The power supply must be replaced if it fails reset when either the TEST
button is pushed or it cannot be reset.
● If power supply cord is damaged, it cannot be repaired. Please call
Consumer Services at 844-472-2473 to assist with replacement.
NOTE:
This air conditioner is designed to be operated under the
following conditions:
Cooling
Operation
Outdoor Temp:
64 – 109°F/18 – 43°C
(64 – 125°F/18 – 52°C for special tropical models)
Indoor Temp:
62 – 90°F/17 – 32°C
Heating
Operation
Outdoor Temp:
23 – 76°F/-5 – 24°C
Indoor Temp:
32 – 80°F/0 – 27°C
Performance may be reduced outside of these operating temperatures.
Grounding Type
Wall Receptacle
Do not, under any
circumstances, cut,
remove, or bypass the
ground prong.
Power supply cord
with 3-prong grounding
plug and current
detection device
Summary of Contents for 3PATW14002
Page 26: ...23...
