-6-
Control Pad On The Dehumidifier
(continued)
AS- Humidity sensor error
Unplug the unit for at least 5 minutes and plug
it back in. If error repeats, call Perfect Aire
Consumer Services at (877)365-6274.
E3- Unit malfunction
Unplug the unit for at least 5 minutes and plug
it back in. If error repeats, call Consumer Services.
Eb- Bucket is removed or not in the correct position.
Remove the bucket and replace it in the proper
position. Ensure float switch is secured properly in
the bucket.
EC- Unit malfunction
Make sure the temperature of the working
environment is between 41°F/5°C and 95°F/35°C.
If not, please operate the unit under the correct
stated temperature. If on a concrete floor, unplug
and elevate unit a few inches off the floor; plug
back into outlet and power on. If you have made
these adjustments and still see the EC error code,
please call Consumer Services.
ES- Temperature sensor error
Unplug the unit for at least 5 minutes and plug
it back in. If error repeats, call Consumer Services.
P2- Bucket is full or not in the correct position.
Empty the bucket and replace it in the proper
position. Ensure float switch is secured properly in
the bucket.
Other Features
Error & Protection Codes
Bucket Full Indicator Light
Illuminates when the bucket is ready to be emptied, is
removed, or is not replaced in the proper position.
Auto Shut Off
The dehumidifier shuts off after 30 seconds when the
bucket is full or when the bucket is removed or not
replaced in the proper position. When the humidity
setting is reached, the unit will cycle off automatically.
(The compressor cycles off first. Three minutes later,
the fan will turn off as well.)
Auto Defrost
When frost builds up on the evaporator coils, the
compressor will cycle off and the fan will continue to
run (on "Turbo") until the frost disappears. The Auto
Defrost Indicator light will illuminate. The unit will
restart on its own once the auto defrost process has
completed.
Safety Feature
After the unit has stopped, it cannot resume operation
in the first 3 minutes afterwards. This is to protect the
unit. Operation will automatically start after 3 minutes.
Check Filter Feature
The system starts to log the time once the fan motor
operates. The check filter light will be lit up only when
the accumulated operation time achieves 250 hours
or more. The Reset light (Clean Filter indicator light)
flashes one time per second. After cleaning the air
filter, press the Filter pad and the Reset light (Clean
Filter indicator light) goes off.
Auto-Restart
If the unit breaks off unexpectedly due to a loss of
power, it will restart with the previous function setting
automatically when the power resumes.
Setting the Timer
• When the unit is on, press the Timer button; the Timer
Off indicator light illuminates, indicating that the Auto
Stop program is initiated. Press it again and the Time
On indicator light illuminates indicating that the Auto
Start is initiated.
• If you prefer, you can set the timer while the unit is
powered off and follow the instructions above to set
the unit to go on and then off.
• Press or hold the UP or DOWN pad to change the
Auto time by 0.5 hour increments, up to 10 hours,
then at 1 hour increments up to 24 hours. The display
on the control pad will count down the time remaining
until start/stop.
• The selected time will register for 5 seconds and the
system will automatically revert back to display the
previous humidity setting.
• When the Auto start and Auto stop times are set
within the same program sequence, TIMER ON and
OFF indicator lights illuminate identifying both ON
and OFF times are now programmed. You can set the
Timer for just ON or just OFF in which case the single
corresponding ON or OFF light will be illuminated.
• Turning the unit ON or OFF at any time or adjusting
the timer setting to 0.0 will cancel the Auto Start/Stop.
• When LED display window displays the code of P2,
the Auto Start/Stop function will also be canceled.
A NOTE ABOUT THE TIMER:
When you set the timer, the unit will only go on
once and off once. If you want the dehumidifier
to cycle on and off repeatedly, you do not need to
set the timer. Instead, set your desired humidity
and the unit will cycle on and off based on that
humidity setting.
