Pepperl+Fuchs PSCAN-D-1D-D2 Installation And Operation Manual Download Page 4

Page: 4 / 85

PSCAN-D-1D-D2 Division 2 Barcode Reader

Subject to modifications

www.pepperl-fuchs.us

USA: +1 330 486 0002

Singapore: +65 6779 9091

Germany: +49 621 776 2222

Product specifications

Laser safety compliance

The barcode reader conforms to the following applicable requirements at

the date of manufacture:

•

EN 60825-1

•

CDRH 21 CFR 1040

The laser light is visible to the human eye and is emitted from the output

window.

Warning! Laser Light

•

The human eye can be damaged.

•

Do not stare into beam of the laser light.

•

Any changes to the device are forbidden. These

could cause a dangerous laser light.

•

Please consider the procedures described in these

operating instructions.

•

Prevent the laser beam from hitting reflective

surfaces such as mirrors, etc.

A warning label is attached to the barcode reader describing the laser

and laser category. The device is a class 2 laser. It is not necessary to

open the barcode reader for installation, application, or maintenance.

Labels cannot be attached to a laser diode. Hence, the respective values

are listed below:

Maximum Output

0.9 mW

Wavelength according to Class 2 N-60825-1

and CDRH21CFR 1040

630-690 nm

Repair and maintenance

The devices must not be repaired, changed, or manipulated. If there is a

defect, the product must always be replaced with an original device.

Applied standards and guidelines

Electromagnetic compatibility

NE 21

Low voltage

ANSI/UL 60950-1-2007

Explosion protection

ANSI/ISA-12.12.01-2007; CSA

C22.2 No. 213-M1987, R2008

Warning

Laser Class 2M

EN 60825-1

PSCAN-D-1D-D2 function

The PSCAN-D-1D-D2EX barcode reader can be used in Class I/Div. 2 and

Class II/Div. 2 hazardous areas. The barcode reader is able to read all

standard 1-D code families. After a successful read, a beep to indicate

a good read is sent out for easy operation. In addition, a bidirectional

communication is possible. Supply and communication of the barcode

reader is made by a nonincendive interface.

Additional functions include:

Aiming system

First, a partial trigger produces a red spot for easy aiming. By completely

pressing the trigger, a line appears to start code scanning.

GL-technics (3 green lights)

A good read is shown via an audio signal, green LEDs on upside and

underside, plus a green scan line directly on the barcode.

Using PSCAN-D-1D-D2 readers

The PSCAN-D-1* barcode reader automatically scans barcodes up to a

certain distance. See the Reading characteristics chart on page xx. Simply

aim and pull the trigger. Code scanning is performed along the scan line

emitted from the reading window. The line must cross the entire code.

Best reading angles

For good reading performance, do not hold the barcode reader vertically.

Use the reading angles in the figure below.

Device components

•

Barcode reader

•

Connecting cable consisting of a helix cable 3 m and a male 4-pin

connector (M12 connector) mounted.

Summary of Contents for PSCAN-D-1D-D2






















































































Search results

Summary of Contents for PSCAN-D-1D-D2

Reviews:

Related manuals for PSCAN-D-1D-D2

Brands by name

Popular brands

Pepperl+Fuchs PSCAN-D-1D-D2, Installation And Operation Manual

Search results

Summary of Contents for PSCAN-D-1D-D2

Reviews:

Related manuals for PSCAN-D-1D-D2

Brands by name

Popular brands