Pepperl+Fuchs IC-KP-R2-V1 Manual Download Page 39 | Manualshive

Page: 39 / 48

background image

Commands

2014-

03

39

Single read special read only code (SS):

The R/W head makes only one attempt to read a

special read only code

.

Enhanced read special read only code (ES):

The R/W head attempts to read a

special read only code

until successful. Only data that

changes is transferred via the interface, i.e. the R/W head transfers data whenever it reads a

new data carrier or whenever it reads a data carrier where there was previously no R/W head

within the detection range.
The status '05h' (read command) is output whenever a data carrier leaves the detection range.

Single program special read only code (SP):

The R/W head makes only one attempt to write a

special read only code

.

Enhanced program special read only code (EP):

The R/W head attempts to write a

special read only code

until successful. After each

successful write, the head sends the response and then switches to continuous reading. Then

the R/W head reads the same data carrier until it has left the detection range or a new data

carrier appears within the detection range. The command then starts again with write attempts.
The status '05h' (read/write command) is output when the data carrier leaves the detection

range or if the data carrier is not yet within the detection range when the command is executed.
If two data carriers enter the read range one immediately after the other, the status '05h' is not

issued between the two readings.

Command:

SS

<Ident channel><FixLen><CHCK><ETX>

Response:

<Status><Ident channel><ID code><CHCK><ETX>

Note!

The <FixLen> of IDC-...-1K read/write tags is always 6 bytes.

Command:

ES

<Ident channel><FixLen><CHCK><ETX>

Response:

<Status><Ident channel><Data><CHCK><ETX>

Note!

The <FixLen> of IDC-...-1K read/write tags is always 6 bytes.

Command:

SP

<Ident channel><FixLen><Data><CHCK> <ETX>

Response:

<Status><Ident channel><CHCK><ETX>

Note!

The <FixLen> of IDC-...-1K read/write tags is always 6 bytes.

Command:

EP

<Ident channel><FixLen><Data><CHCK> <ETX>

Response:

<Status><Ident channel><CHCK><ETX>

Note!

The <FixLen> of IDC-...-1K read/write tags is always 6 bytes.

«
...
37
38
39
40
41
...
»

Summary of Contents for IC-KP-R2-V1

















































Reviews:

No comments

Related manuals for IC-KP-R2-V1

Brand: MacDon Pages: 272

Brand: MacDon Pages: 70

Brand: Parr Instrument Pages: 24

Brand: JBL Pages: 15

Brand: idiag Pages: 10

Brand: Bandit Pages: 136

Versaflo S Series

Brand: 3M Pages: 11

DBI Sala EXOFIT

Brand: 3M Pages: 32

Brand: 3M Pages: 8

Brand: Accurate Bio-Medical Technology Pages: 35

Brand: Abus Pages: 2

Brand: Abus Pages: 12

Brand: Abu Garcia Pages: 6

Brand: Unitary products group Pages: 28

Brand: Jacobsen Pages: 20

Brand: jablotron Pages: 2

Brand: Rapala Pages: 14

Brand: S.R.Smith Pages: 43

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands