Pepperl+Fuchs IC-KP-R2-V1 Manual Download Page 38 | Manualshive

Page: 38 / 48

background image

2014-

03

38

Commands

The R/W head constantly attempts to write a read only code. After each successful write, the

response is sent and the system waits until a new tag is within the detection range. The

command then starts again from the beginning.

Set tag ID code (TI):

This command restricts the execution of all other read/write commands to the read/write tag

with the specified ID code. This also applies if another read/write tag is located within the

detection range. A targeted response is achieved from the read/write tag as a result.
<ByteNum> = 0h: Do not make a selection. An ID code is not specified in the telegram.
<ByteNum> = 8h (System IQ): Make a selection. An ID code must be specified in the telegram.
<ByteNum> = 0h deletes this filter.

Fill data carrier (S#):

The word number <WordNum> of fill signs <Fill Sign> is written to the read/write tag from the

specified start address <WordAddr>.

Extended commands for type IDC-... and IUC

…

tags

Type IDC-...-1K tags can be programmed to read 24-bit information (so-called

special read

only code)

very quickly. This is useful for detecting containers in automated warehouses.

To write the

special read only code

use the commands

SP

and

EP

; to read it out, use the

commands

SS

and

ES

.

If

SP

or

EP

is used to write to an IDC-...-1K tag, the tag is then locked. If you wish to write to the

tag again using standard commands, unlock it using the command

SI

.

IPC11:

<FixLen>

=

5

<FixType>

=

'02' ASCII (30h 32h), the read only code cannot be

changed

'11' ASCII (31h 31h), the read only code can be

overwritten

IDC-...-1K:

<FixLen>

=

7

1

<FixType>

=

'52' ASCII (35h 32h), the read only code can be

overwritten

1. The first 3 bytes are hexadecimal (0h ... Fh), the last 4 bytes are decimal (0d ... 9d).

Command:

TI

<Ident channel><Bytenum><ID code> <CHCK><ETX>

Response:

<Status><Ident channel><CHCK><ETX>

Note!

The TI command only adjusts a setting in the reading head. There is no HF communication

with the read/write tags.

Command:

S#

<Ident channel><WordAddr><WordNum><Fill Sign><CHCK><ETX>

Response:

<Status><Ident channel><CHCK><ETX>

Length of the

special read only code

:

■

Tag of the type IDC-...-1K:

48 bit

■

Tag of the type IUC:

96 ... 240 bit

«
...
36
37
38
39
40
...
»

Summary of Contents for IC-KP-R2-V1

















































Reviews:

No comments

Related manuals for IC-KP-R2-V1

Brand: Baker Instrument Company Pages: 24

Brand: Keithley Pages: 36

Brand: Rain-Flo Irrigation Pages: 16

Brand: Bahco Pages: 9

Brand: Bang & Olufsen Pages: 2

Brand: Kärcher Pages: 20

Brand: Parker Research Corp Pages: 3

Brand: Kellfri Pages: 44

Brand: Rigol Pages: 12

Brand: Lites Pages: 8

Brand: Tascam Pages: 100

Brand: K-SPORT Pages: 5

Brand: Brillion Pages: 56

Brand: Conrad Pages: 34

Brand: Tadano Pages: 16

Brand: Yellowtec Pages: 27

Brand: WALU Pages: 4

B-Control Deejay BCD3000

Brand: Behringer Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands