background image

CP345

Preface

ID 19979, Rev. 03

Page v

© 

PEP Modular Computers GmbH

Preface

Proprietary Note

This document contains information proprietary to 

PEP Modular Computers. It may not be

copied or transmitted by any means, disclosed to others or stored in any retrieval system or
media, without the prior written consent of 

PEP Modular Computers GmbH or one of its autho-

rized agents.

The information contained in this document is, to the best of our knowledge, entirely correct.
However, 

PEP Modular Computers cannot accept liability for any inaccuracies, or the conse-

quences thereof, nor for any liability arising from the use or application of any circuit, product,
or example shown in this document.

PEP Modular Computers reserve the right to change, modify, or improve this document or the
product described herein, as seen fit by 

PEP Modular Computers without further notice.

Documentation Overview

This manual has been written for OEM software and hardware engineers to correctly under-
stand the features and specifics of the product described in it. The manual is intended also for
professional training purposes.

Trademarks

PEP Modular Computers GmbH, the PEP logo and, if occurring in this manual, “CXM” are
trademarks owned by 

PEP Modular Computers GmbH, Kaufbeuren (Germany). 

In addition, this document may include other names, company logos and trademarks, which
are registered trademarks and, therefore, proprietary to their respective owners.

Related Publications

For any details not described in the product documentation of the CP345 serial controller
board, please refer to the following publications.

PICMG CompactPCI Specification, V. 2.0, Rev. 3.0

PCI Special Interest Group: PCI Local Bus Specification, V. 2.1 of 1 June 95

PEP Modular Computers GmbH: CompactPCI System Manual, ID 19954

Summary of Contents for CP345

















































































Reviews: