Maintenance (Continued)
10. Remove slinger from motor shaft
and inspect for damage or
abrasion.
11. Clean seal cavity in seal plate and
clean motor shaft.
PUMP REASSEMBLY/INSTALLING
NEW SEAL
1. Ceramic seat must be clean and free
of dirt, grease, dust, etc. Wet outer
edge with small amount of liquid
detergent; press ceramic seat into
seal plate cavity firmly and squarely
with finger pressure (See Figure 6).
2. If ceramic seat will not locate
properly, remove it, place
face up
on bench and reclean cavity.
Ceramic seat should now locate.
3. If seat still will not locate properly,
place a cardboard washer over the
polished face and use a piece of
3/4" (19mm) standard pipe for
pressing purposes.
NOTE:
Be sure not to scratch or mar
polished surface or seal will leak.
4. Replace slinger on end of motor
shaft so that impeller sleeve will
push it into position. If slinger
shows signs of wear or damage,
replace it.
5. Remount seal plate on motor.
Tighten bolts to 60-80 inch-lbs.
(69-92 kg/cm) torque.
6. Apply a
small
amount of liquid
detergent to inside diameter of
rotating half of seal.
7. Slide rotating seal member,
polished carbon face out, over
impeller sleeve until rubber drive
ring hits back of impeller.
NOTE: Be sure
not to nick or scratch
polished seal face; seal will leak if face
is damaged.
8. Screw impeller onto shaft
(clockwise); this will automatically
locate seal in seal plate.
NOTE:
On 2 and 2
1
⁄
2
HP models; install
impeller gasket and lock screw (left-
hand thread - turn counterclockwise).
Torque lock screw to 50-55 inch-lbs.
(57.6-63 kg/cm).
9. Mount diffuser on seal plate;
tighten screws to 10-14 inch-lbs.
(11.2-16.1 kg/cm) torque.
10. Assemble motor and seal plate to
pump body with nuts, flat washers,
and lock washers. Torque nuts to
120-130 in-lbs. (138-150 kg/cm).
11. Prime pump according to
instructions on Page 5.
Models 4RJ93, 4RJ94 and 4RJ95
7
Teel Operating Instructions and Parts Manual
®
E
N
G
L
I
S
H
Figure 6
Polished
surface
Rubber
surface
Limited Warranty
DAYTON ONE-YEAR LIMITED WARRANTY.
Teel
®
pool pump with integral trap, Models covered in this manual, are warranted by Dayton Electric Mfg. Co.
(Dayton) to the original user against defects in workmanship or materials under normal use for one year after date of purchase. Any part which is determined
to be defective in material or workmanship and returned to an authorized service location, as Dayton designates, shipping costs prepaid, will be, as the
exclusive remedy, repaired or replaced at Dayton’s option. For limited warranty claim procedures, see PROMPT DISPOSITION below. This limited warranty gives
purchasers specific legal rights which vary from jurisdiction to jurisdiction.
LIMITATION OF LIABILITY.
To the extent allowable under applicable law, Dayton’s liability for consequential and incidental damages is expressly disclaimed.
Dayton’s liability in all events is limited to and shall not exceed the purchase price paid.
WARRANTY DISCLAIMER.
Dayton has made a diligent effort to provide product information and illustrate the products in this literature accurately; however,
such information and illustrations are for the sole purpose of identification, and do not express or imply a warranty that the products are MERCHANTABLE, or
FIT FOR A PARTICULAR PURPOSE, or that the products will necessarily conform to the illustrations or descriptions.
Except as provided below, no warranty or affirmation of fact, expressed or implied, other than as stated in the “LIMITED WARRANTY” above is made or
authorized by Dayton.
PRODUCT SUITABILITY.
Many jurisdictions have codes and regulations governing sales, construction, installation, and/or use of products for certain purposes,
which may vary from those in neighboring areas. While Dayton attempts to assure that its products comply with such codes, it cannot guarantee compliance,
and cannot be responsible for how the product is installed or used. Before purchase and use of a product, review the product applications, and all applicable
national and local codes and regulations, and be sure that the product, installation, and use will comply with them.
Certain aspects of disclaimers are not applicable to consumer products; e.g., (a) some jurisdictions do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you; (b) also, some jurisdictions do not allow a limitation on how long an implied
warranty lasts, consequently the above limitation may not apply to you; and (c) by law, during the period of this Limited Warranty, any implied warranties of
implied merchantability or fitness for a particular purpose applicable to consumer products purchased by consumers, may not be excluded or otherwise
disclaimed.
PROMPT DISPOSITION.
Dayton will make a good faith effort for prompt correction or other adjustment with respect to any product which proves to be
defective within limited warranty. For any product believed to be defective within limited warranty, first write or call dealer from whom the product was
purchased. Dealer will give additional directions. If unable to resolve satisfactorily, write to Dayton at address below, giving dealer’s name, address, date, and
number of dealer’s invoice, and describing the nature of the defect. Title and risk of loss pass to buyer on delivery to common carrier. If product was damaged
in transit to you, file claim with carrier.
Manufactured for Dayton Electric Mfg. Co., 5959 W. Howard St., Niles, Illinois 60714 U.S.A.
