background image

3

GENERAL INFORMATION

• Clean a new pool as well as possible before filling pool and operating

filter. Excess dirt and large particles of foreign matter in the system can
cause serious damage to the filter and pump.

• With a permanent media filter in place and operating correctly, clean water

is returned to the pool faster than pool water is being contaminated. A
typical pool installation will require approximately one week to obtain and
maintain the sparkle that your filter is capable of giving you.

• Maximum pressure is 50 PSI (345 kPa). DO NOT connect the filter to a

city water system or to an individual water well system.

Hazardous pressure. Open air release valve to vent all air

from system before operating system. NEVER operate filter with air

trapped inside.

• The Sta-Rite

®

modular media filter is designed to filter water for swimming

pools and spas. On a new installation, we recommend:

1. Disassemble the filter after the initial cleanup.

Hazardous pressure. To prevent severe injury or major

property damage, exactly follow "Filter Disassembly/Assembly

Procedure" on Pages 6 and 7.

2. Remove and hose down the element assembly to remove contaminants.

• Maintain pool water pH between 7.2 and 7.6.

• Make sure that internal air bleed tube and filter are clean and installed

properly at top of module before operating filter.

• Make sure that Posi-Lok™ Ring is securely locked in place before

operating filter.

• Maintain pressure gauge in good working order. Replace a damaged

gauge immediately.

• Cleaning interval is based on pressure rise, not on length of time filter is

operated. Different water conditions will have different normal cleaning
intervals.

• Check local codes for restrictions on waste water disposal requirements.

NOTICE: Some pool disinfectants may clog filter module. To maximize
module life and filter cycle time, closely follow disinfectant manufacturer’s
instructions when cleaning pool or filter. Failure to follow these instructions
may affect warranty coverage of the module.

Owner’s Information

Serial Number ______________________________________________

Dealer ____________________________________________________

Dealer’s Telephone # _________________________________________

Purchase Date ______________________________________________

Pressure Gauge Reading at Startup _____________________________

Installation Date _____________________________________________

When to Clean the Filter

The filter module should normally be
cleaned when the pressure gauge
reading increases 10 PSI over the start-
up pressure (record the start-up
pressure under “Owner’s Information”,
below, right).

In some pools, accessories such as
fountains or pool cleaners may be
noticeably affected by the normal
decrease in flow as the filter becomes
dirty. If so, clean the filter more
frequently (that is, at a pressure increase
of less than 10 PSI) in order to maintain
the required flow.

He
a

d

Bo

dy

F

or

e

A

rm

U

ppe

r

Arm

Le

g

Jo

int

Le

g

Join

t

L

e

g

Jo
in

t

He
ad

Bod

y

WARNING

Risk of drowning and
falls. Place equipment 
at least 4 feet from pool 
so that children cannot
climb over it into pool.

sss

Do not allow children
to stand or play on filter
or pump.

Summary of Contents for STA-RITE PLM100













Reviews: