background image

EnviroMAX 800

Variable Speed Pool Pump

IMPORTANT

Please attach your sales invoice/docket here as proof of purchase 

should warranty service be required.

Purchased from:......................................................................................................................................

Purchase date: ........................................ Serial No.: ................................... Model No.: ......................

Head Office

Pentair AU/NZ: 

 

 

1-21 Monash Drive

    Dandenong 

South, 

    VIC 

3175

National customer service:  

Phone:  1300 137 344

    Fax: 

1800 

006 

688

National dealer locator:    

Phone:  1800 664 266

Email: 

 

   [email protected]

Web: 

 

   www.pentairpool.com.au

© Information contained here-in remains the property of Pentair Australia Pty Ltd. Any reproduction, 

display, publication, modification or distribution is strictly prohibited without the prior written permission 

of Pentair Australia Pty Ltd.

Disclaimer:

Every endeavour has been made to publish the correct details in this document. No responsibility will be 

taken for errors, omissions or changes in product descriptions, specifications. Pentair Australia reserves 

the right to change specifications.

L300294 A0318

Summary of Contents for Sta-Rite EcoSelect Enviromax 800





















Reviews: